A Two-Wire DC Distributor Cable (AB) is 2 km long and supplies loads of 100 A, 150 A, 200 A, and 50 A situated 500 m, 1000 m, 1600 m and 2000 m from the Feeding Point A. Each conductor has a Resistance of 0.02 2 per 1000 m. Calculate the PD at each Load Point if a PD of 300 V is maintained at Point A.

A Two-Wire DC Distributor Cable (AB) is 2 km long and supplies loads of 100 A, 150 A, 200 A, and 50 A situated 500 m, 1000 m, 1600 m and 2000 m from the Feeding Point A. Each conductor has a Resistance of 0.02 2 per 1000 m. Calculate the PD at each Load Point if a PD of 300 V is maintained at Point A.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.1P: The Aluminum Electrical Conductor Handbook lists a dc resistance of 0.01558 ohm per 1000 ft at 20C...

See similar textbooks

Similar questions

The Aluminum Electrical Conductor Handbook lists a dc resistance of 0.01558 ohm per 1000 ft at 20C and a 60-Hz resistance of 0.0956 ohm per mile at 50C for the all-aluminum Marigold conductor, which has 61 strands and whose size is 1113 kcmil. Assuming an increase in resistance of 2 for spiraling, calculate and verify the dc resistance. Then calculate the dc resistance at 50C, and determine the percentage increase due to skin effect.
E A 2-wire d.c. ring distributor is 400 m long and is fed at 240 V at point A. At point B, 150 m from A, a load of 150 A is taken and at C, 100 m from B, with load of 40 A and at D, 25m in the opposite direction from A, a load of 200 A is taken. If the resistance per 100 m of single conductor is 0.04 22, find: (i) Current in each section of distributor (ii) Voltage at points B, C and D.
5. A 2-wire DC ring distributor is 375m long and is fed with 300V at point A. At point B, 200m from A, load of 150A is taken and at point C, 100m in the opposite direction, a load of 100A is taken. If the resistance per 100m of single conductor is 0.03, find: i. Current in each section of distributor ii. Voltage at points B and C iii. Point of minimum potential
A two wire DC distributor AB, 1000 meter long, is supplied from both ends, 240 V at A and 242 V at B. There is a concentrated load of 200 A at a distance of 400 meter from A and a uniformly load 1.0 A/m between the midpoint and end B. Determine (i) the current fed at points A and B (ii) the point of minimum potential and (iii) voltage and this point. Consider cable resistance as 0.005 ohm per 1000 meter each core.
A 2-wire d.c. ring distributor is 300 m long and is fed at 240 V at point A. At point B, 150 m from A, a load of 120 A is taken and at C, 100 m in the opposite direction, a load of 80 A is taken. If the resistance per 100 m of single conductor is 0.030. find: (i) current in each section of distributor (ii) voltage at points B and C.
A 30 kV single core cable has a conductor dimeter of 2 cm and a sheath of inside diameter 6 cm. Find the maximum (peak value) and minimum stress (peak value) in the insulation.
Single core cable design for 25 kV. The radius of conductor is 0.5 cm. The insulation material consists of two layers. The thickness of each layer is 2 cm. The voltage of first and second layers are 20 kV, 5 kV respectively. The maximum Electric stress of the cable is
A 2-wire d.c. distributor cable AB is 3 km long and supplies loads of 100A, 150A,200A and 50A situated 600 m, 1000 m, 1500 m and 2000 m from the feeding point A. Each conductor has a resistance of 0.02 ohm per 1000 m. Calculate the p.d. at each load point if a p.d. of 350 V is maintained at point A.
A 2-wire d.c. distributor cable AB is 2 km long and supplies loads of 100A, 150A,200A and 50A situated 500 m, 1000 m, 1600 m and 2000 m from the feeding point A. Each conductor has a resistance of 0-010 per 1000 m. the p.d. at each load point if a p.d. of 300 V is maintained at point A is: * O no one of the answers (a, b & c) VA=300V; VC=289V; VD=285V; VE=281V; VB=793V VA=300V; VC=270V; VD=265V; VE=260V; VB=255V VA=300V; VC=295V; VD=291V; VE=288V; VB=287.6V
A 650 m, 2-wire d.c. distributor fed from one end is loaded uniformly at the rateof 1-6 A/metre. The resistance of each conductor is 0.0456 ohm per metre. Find the voltage necessary at feed point to maintain 240 V (i) at the far end (ii) at the mid-point of the distributor.
:Two circuits are arrange as shown in figure (1), (a and b) each one of them has two identical conductors, the vertical distance between each conductor in the same circuit is 1 m, the distance horizontlly between circuits is 30 cm, take 1 cm as diamter for each conductors. Derermine the inductance per km of the double circuit ? a a' b' FIGURE (1) --
A 33 kV single core cable has a conductor diameter of 1 cm and a sheath of inside diameter 4 cm. Find the maximum and minimum stress in the insulation.