A two-legged core is shown in the figure. The winding on the left leg (N1) has 600 turns, and the winding on the right (N2) has 200 turns. The coils are wound in the directions shown in the figure. If the dimensions are as shown, then what flux will be produced by currents il = 0.5 A and i2 =1.0 A? Assume µr =1000 and constant. 15 dey 5m

A two-legged core is shown in the figure. The winding on the left leg (N1) has 600 turns, and the winding on the right (N2) has 200 turns. The coils are wound in the directions shown in the figure. If the dimensions are as shown, then what flux will be produced by currents il = 0.5 A and i2 =1.0 A? Assume µr =1000 and constant. 15 dey 5m

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A ferromagnetic core is shown in Figure Pl-2. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. Find the value of the current that will produce a flux of 0.005 Wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 800. 1-5. 10 cm- 5em 20 em 15 cm 15 cm 15 cm Coe depth - Scm SOLUTION There are three regions in this core. The top and bottom form one region, the left side forms a second region, and the right side forms a third region. If we assume that the mean path length of the flux is in the center of each leg of the core, and if we ignore spreading at the corners of the core, then the path lengths are I, = 2(27.5 cm) = 55 cm, I, = 30 cm, and /, = 30 cm. The reluctances of these regions are:
A toroidal core with a mean circumference of 100 cm and a cross-sectional area of 10 cm2 is wound with 500 turns of wire. What current would be required to generate a flux of 1 mWb in the core. Assume the core has a relative permeability of 800
Question: 01 A two-legged core is shown in figure below. The winding on the left leg of the core (N) has 800 turns. The depth of the core is 15 cm. The small airgap is 0.05 cm and there is no fringing effect. If the dimensions are as shown, then determine the total reluctance of the given core when u, =800 and constant. 15cm 25cm 10cm 10cm 50cm N=800 5cm
Question 1 A ferromagnetic core is shown in Figure 1. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. a) Find the value of the current that will produce a flux of 0.005 Wb. b) With this current, what is the flux density at the top of the core? c) What is the flux density at the right side of the core? Assume that the relative permeability of the core is 1000. cm -10 cm-- 20 cm 15 cm 500 turns 15 cm 15 cm Core depth 5 cm Figure 1
1.Consider the magnetic core below.All dimensions are shown on the figure. The core is made up of legs with 2 different cross-sectional areas.The depth of core is 10cm.The relative permeability of the core is 2000. The current in the magnetising coil is 1 A. The number of turns of the coil is 2000.Calculate: (i)the reluctances and draw the magnetic circuit (ii)the flux in the core (iii)Flux densities B and field intensities H in legs having different cross-sectional areas. (iv)Verify Ampere's Law. Depth: 10 cm I=1A 20cm 2000 Turns 65cm 15cm 15cm 50cm 15cm ndo un of
2. A two-legged core is shown in figure below. The winding on the left leg of the core (N,) has 600 turns, and the winding on the right (N2) has 200 turns. The coils are wound in the directions shown in the figure. If the dimensions are as shown, then what flux would be produced by currents i, = 0.5 A and iz = 1.00 A? Assume p, = 1000 and constant. -15 cm+ +i5 cm 15 cm 600 turns 200 turms 15 cm core depth- 15 cm [0.0054 Wb]
The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the corelaminations have a thickness of 0.50 mm. The core is redesigned so as to operate with the same eddycurrent loss but at a different voltage and at a frequency of 250 Hz. Assuming that at the new voltage themaximum flux density is one-third of its original value and the resistivity of the core remains unaltered,determine the necessary new thickness of the laminations. Clear and detailed solution.
A ferromagnetic core is shown below. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. Find the value of the current that will produce a flux of 0.003 Wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 1000. 1. - 10 cm--- - 20 cm - 15 cm 500 tums 15 cm 15 cm [1.21 A, 0.4 T, 1.2 T]
A 10, 120 V, 60 Hz supply is connected to the coil The coil has 200 turns. The parameters of the core are as follows: Length of core = 100 cm Cross-sectional area of core = 20 cm? Relative permeability of core = 2500 Obtain an expression for the flux density in the core.
ferromagnetic core is shown in Figure P1-2. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. Find the value of the current that will produce a flux of 0.005 Wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 800. -10cm- -20 cm- 500 turns a. 670 kA t/Wb b. 330 kA t/Wb c. 500 kA t/Wb d. 256 kA t/Wb Core depth = 5 cm 15cm + 15cm 15cm 5 E
Problem 1A core with a coil has 240 turns, to generate a flux ø of 0.008482 weber, how much should the current i1 be and what will its direction be? Relative permeabilities: metal 1 of 250 and metal 2 of 375. Core depth 25cm
A current in a 250 turn coil is 2.25A, wound in a core that has a reluctance of 12,000 AT/Wb. What is the resulting flux density (in Tesla), if the area of the core is 8cm²?