A tank has two rooms separated by a membrane. Room A has 1 kg of air and a volume of 0.5 m3; room B has 0.75 m3 of air with density of 0.8 kg/m3. The membrane is broken, and the air comes to a uniform state due to mixing. Mixing is considered to be? what is the answer a. Property b. Final State c. Initial state d. process

A tank has two rooms separated by a membrane. Room A has 1 kg of air and a volume of 0.5 m3; room B has 0.75 m3 of air with density of 0.8 kg/m3. The membrane is broken, and the air comes to a uniform state due to mixing. Mixing is considered to be? what is the answer a. Property b. Final State c. Initial state d. process

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 29RQ: If 3000 ft3 of air is crossing an evaporator coil and iscooled from 75F to 55F, what would be the...

See similar textbooks

Similar questions

If 3000 ft3 of air is crossing an evaporator coil and iscooled from 75F to 55F, what would be the volume of air, in ft3, exiting the evaporator coil?
A piston cylinder assembly initially contains 5 kg of water, a saturated liquid-vapor mixture at a pressure of 100 kPa. 2 kg of water is in liquid phase and the rest is in vapor phase. In this state, the piston is on the stoppers. Then there is heat transfer to water, pressure rises and when 150 kPa the piston movesbegins to do. Heat transfer continues until the total volume is twice the initial volume. According to this; a) Draw the T-v and P-v diagram of the process. b) Initial and final temperatures, c) Calculate the mass of water in the liquid phase when the piston starts to move upwards.
A 100-liter tank contains a mixture of saturated liquid water and saturated steam at 370 °C. a) Find the mass of each phase if their volumes are equal b) Find the volume occupied by each phase if their masses are equal. b) Find the volume occupied by each phase if their masses are equal. Given: Vf = 2.213x10^-3 m^3/kg; vg = 4.925x10^-3 m^3/kg
4. A 100 liter tank contains a mixture of saturated liquid water and saturated steam at 370 °C. a) Find the mass of each phase if their volumes are equal b) Find the volume occupied by each phase if their masses are equal. Given: v = 2.213x103 m³/kg; vg = 4.925x103 m³/kg
A tank contains 2.000 gallon of brine. Brine containing 5 lb/gallon of salt flows in at a rate of 10 gallon/minute. The mixture kept uniform by stirring, flows out at a rate of 20 gallon/minute. If the concentration of the salt is 8 lb/gallon at the end of 1 hour, how much was the concentration of the salt at the beginning?
Which of the following statement is correct? Select one: O a. point functions are inexact Differential. O b. Point functions are not the properties of the system. O c. The Point Function depends on the path followed during a process as well as the end states. O d. Examples for points functions are temperature, pressure, density.
B: Choose the correct answer: 1. (A collection of matter within prescribed and identifiable boundaries) this definition refer to: B. Closed system thermodynamic System A. Open System 2. 0.05 kg of Steam contained in a rigid vessel of volume 0.0076 m' with a pressure 15 bar. The temperature of steam will be: A. 258 °C B. 250 °C C. 245 °C 3. The energy associated with the motions of the microscopic particles comprising a macroscopic system) this definition refer to: A. Internal Energy B. Enthalpy C. Pressure 4. When a liquid is heated at any one constant pressure there is one fixed temperature at which bubbles of vapour form in the liquid, this phenomenon is known as: A. Saturation B. Boiling C. Heating 5. its defined as a state at which a change of phase of phase may occur without change of pressure or temperature A. Critical point B. Latent heat of vaporization C. Saturation 6. The heat required to change a saturated liquid to a dry saturated vapour is called: A. Latent heat B.…
In a certain semiconductor plant, the following condition exist on the intake side of thecompressor:Intake temperature - 28oCRelative humidity - 70%Volume of air drawn - 1,000 m3/hAfter compressing air to 7 bar, temperature rises to 40oC. Determine the following:a) Quantity of water before compressionb) Quantity of water after compressionc) Quantity of water occurring in the production aread) Total amount of water precipitated in the system
m and 5 Kg Kg 2. Three liquids of different qualities, p1 = 1500 , V2 = .002 m3' Liters of water, are poured together into a 30 gallons tank, filling it. If Kg the resulting density of the mixture is 1,200 m3' find the respective quantities of liquids. Also, find the weight of the mixture.
i. Draw a P-V graph to represent the changes undergone by the air ii. Calculate the maximum volume of the air. iii. What is the maximum pressure of the air? iv. State how the net work done on the air for the whole process can bedetermined.
While the pressure remains constant at 700 kPa the volume of the system of hydrogen changes from 0.6 m3 to 0.2 m3. What are a) the change of internal energy, b) the change enthalpy, c) the change of entropy, d) heat and e) work for nonflow?
c) A piston cylinder assembly initially contains water at 75 kPa and 8 percent quality (x = 0.08) with a volume of 2 m². The water is then heated until its pressure is 400 kPa. During this process, the pressure and volume are related by P = av + b, where a = 50 kPa/m³ and b = -25 kPa. Both 'a' and 'b' are constants. i) Determine the specific volume (m/kg), specific internal energy (kl/kg) and mass (kg) of water at the initial state. ii) Determine the specific volume (m/kg) and specific internal energy (kJ/kg) of water at the final state. ii) Sketch the process on a pressure (kPa) versus volume (m³) diagram and label all properties. iv) Determine the work done (kJ) and heat transferred (kJ) during the process. v) Describe another method of calculating the work done other than the method you used in part (iv) above. Show the calculation to obtain the work done using this second method.