A solid steel cylinder is enclosed by a hollow copper cylinder; both cylinders are 250 mm long at 20 oC. The cross-sectional area of the steel is 30 cm2 and the copper is 80 cm2 . A load of 160 kN is applied to the composite column by means of rigid cover plates. Calculate at what temperature the steel will carry the full load.

Q: A steel bar of 40 mm x 40 mm square cross section is subjected to an axial tensile load of 200 kN.…

A: Given , dimensions of the steel rod =40mm×40mm Axial tensile load, P=200kN=200×103N Length of the…

Q: Determine the total deformation of the steel rod shown in figure (1) under the given loads. Take the…

A: The loads in the different segments of the composite rod are,

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy…

A:

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

A:

Q: 1. Steel bars AB, CD and EF (E=200 GPa) are under the influence of 36 kN P load. bars AB and CD each…

A: The force which is incident towards a cross-section is termed a compressive force. The stress which…

Q: A load is applied to a rigid bar that is symmetrically supported by three steel rods, as shown. The…

A: here the cross- section of the rod is A  A= 1.2 in2 stress = 22000 psi

Q: A load Pis supported by a structure consisting of rigid bar ABC, two identical solid bronze (E -…

A:

Q: A 11-m uniform beam is hinged to a vertical wall and held horizontally by a 5.0-m cable attached to…

A:

Q: The steel rod is stress-free before the axial loads P1 =169 kN and P2 = 88 kN are applied to the…

A:

Q: Question 3: Find the extension in mild steel wire of 10 mm in diameter and 1.6 m long, the wire is…

A: Given, Diameter of the steel wire = d = 10 mm Length of the wire = 1.6 m = 1600 mm Axial load on the…

Q: The pin-connected structure consists of two cold-rolled steel [E = 28,000 ksi] bars (1) and a bronze…

A:

Q: A column is made from a rectangular bar whose cross section is 5.1 cm by 8.7 cm If the height of the…

A:

Q: A hollow copper cylinder surrounds a solid aluminum cylinder and the assembly is subjected to an…

A: Given Data  Area of the copper is :Ac=20 cm2 Area of the aluminum is : Aal=60 cm2 Length of the…

Q: A load Pis supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

A:

Q: 1. A steel bar 8 m long, hanging vertically supports a tensile load of 2500 N. Neglecting the weight…

A:

Q: A rod of diameter 50 cm and length 6 m is hanging vertically and carries an axial load of 10 kN at…

A: Self weight of the rod below the 2m mark from the bottom  Volume of rod hanging below 2m maek =…

Q: Q2: A composite bar is made up two vertical rods of steel and copper each of length 2 m and diameter…

A: from the above figure given data is load is 15KN in the given question find out each load on the…

Q: A steel hoop. 10 mm thick and 80 mm wide, with inside diameter 1500.0 mm. 5. Is neated and shrunk…

A:

Q: A steel hoop, 10 mm thick and 80 mm wide, with inside diameter 1500.0 mm, is heated and shrunk onto…

A:

Q: Find the pull force P that will make the total elongation of the system 0.04 mm. b) Calculate the…

A:

Q: A leaf spring is to be made of seven steel plates 6-5 cm wide and 6.3 mm thick. Calculate the length…

A: A leaf spring is made up of seven steel plates that are 6.5 cm broad and 6.3 mm thick.We must choose…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

A: The supporting structure is connected with three rods middle rod is steel and the ends rods are made…

Q: A round steel shell with outer and inner diameter 12 mm and 8 mm, respectively, encloses a brass…

A:

Q: If you double the length of a column by what factor is it buckling load

A: Given data Double the length of a column

Q: 14 The brass bar shown is loaded axially in compression so that the maximum stress induced is 125…

A: Given   Maximum stress = 125 MPa         Diameter, D = 30 mm Hole diameter, d = 20 mm Find  Total…

Q: Two 300 mm x 120 mm I-section joists are united by 12 mm thick plates as shown in Figure 2 to form a…

A: The relevant properties of each joist are, Ixx=96X10-6 m4, Iyy=4.2X10-6m4, A=6X10-3m2

Q: 2. The steel structure shown is subjected to the load P-1000 lb. Assume the cross-sectional area be…

A: Given: P=1000 lbA=0.05in2l=10 in.R=5 in.E=10×106 psi

Q: A steel tube, 25 mm outside diameter and 12mm inside diameter, cames an axial tensile load of 40 kN.…

A: GivenD=25 mm=0.025md=12 mm=0.012mF=40 kN=40×103 Nσmax=225 MN/m2=225 ×106 N/mAskedσ=?Fmax=?

Q: A 5-m high aluminum cylinder must support a load of 450 kN. If the maximum allowable stress is 0.14…

A: Write the given values along with the suitable variables.

Q: 213. The rigid bar AB, attached to two vertical rods as shown in Fig. P-213, is horizontal before…

A:

Q: The rigid, horizontal slab is attached to two identical copper rods. There is a gap = 0.18 mm…

A: Given data: Gap between aluminum rod and slab = ∆ = 0.18 mmThe temperature is increased by 85°C.Area…

Q: A steel rod of 30 mm diameter is subjected to a 10 kN of axial load. The length of the steel rod is…

A:

Q: A bar of triangular cross section with base 15mm carries a load of 100 kN. Calculate its minimum…

A:

Q: QUESTION 3: Square profile made of hollow 1045 steel, with a length of 6 meters with a…

A: Given data: Cross-section of Square hollow profile of steel pipe is drawn below. Cross-sectional…

Q: A steel rod of length 10 m is subjected to a axial load of 10 kN. Calculate the elongation of the…

A: Given data  Length of steel rod (L) = 10 m  Axial load (P) = 10 kN diameter (d) = 40 mm E = 200 GPa…

Q: A steel rod, 20 mm diameter and 800 m long, is rigidly attached to an aluminium rod, 40 mm diameter…

A:

Q: 1. A steel bar 8 m long, hanging vertically supports a tensile load of 2500 N. Neglecting the weight…

A:

Q: A steel bar with a cross-section 25mm x 50mm is acted upon by the axial forces as shown. What is the…

A:

Q: To support a tensile load of 65 kN, a metallic rod with a circular cross section and a length of…

A: If two design criteria are given for a system, the design should be made on the criteria that give…

Q: Problem 3: (M4) Your boss at a construction company asked you to verify the thickness of a 3 m long…

A:

Q: 1. A wire of metal with a diameter of 1 cm and a length of 10 m is intended to be used to lift…

A:

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

A: Series Combination:- Series combination of bars is a type of series where axial deflection is…

Q: Rigid bar ABCD is loaded and supported. Bars (1) and (2) are unstressed before the load P is…

A:

Q: To support a tensile load of 65 kN, a metallic rod with a cross-sectional area of Circle and a…

A: Given dataMaximum tensile load on the rod P = 65kNCross sectional area A = ?Length of the rod L =…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

A:

Q: Q5/ Calculate the maximum stress in a round steel bar, 200 mm diameter and 15 m long. due to its own…

A: Given data: d=200 mmL=15 mρ=7.75 mg/m3 Need to determine the maximum stress in the round steel bar.…

Q: A hollow copper cylinder surrounds a solid aluminum cylinder and the assembly is subjected to an…

A: Write the given values along with the suitable variables.

Q: A steel bar 50 mm in diameter and 2 m long is surrounded by a shell of a cast iron 5 mm thick.…

A:

Q: (a) Two vertical rods, one of steel and other of copper are each rigidly fixed at the top and 60 cm…

A: Write the expression of the cross-sectional area of the rods.           Understand that the…

Q: A leaf spring 1 m long is made up with steel plates with width equal to 6 times its thickness.…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.