A single phase autosequential CFI is fed from a 220 Vde source, R_{L} = 10Omega the thyristor turn off tq time equals to 20 us and frequency is 50 Hz. Determine suitable value of source inductance assuming a maximum current change di/dt of 0.5A per cycle. Neglecting all losses, calculate able the value of operating capacitor C.

A single phase autosequential CFI is fed from a 220 Vde source, R_{L} = 10Omega the thyristor turn off tq time equals to 20 us and frequency is 50 Hz. Determine suitable value of source inductance assuming a maximum current change di/dt of 0.5A per cycle. Neglecting all losses, calculate able the value of operating capacitor C.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

Section [Section Upload answer sheets Find the following parameters of an ac voltage given by the equation v-100sin370t.Find RMS value,form factor, peak factor, average value and frequency. E Submission
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of158 volts, 50 Hz supplies the combination. Determine the following:a. Circulating currentb. Voltage across the resistorc. Voltage across the capacitord. Real power supplied by the source
Define electronegative gases and Compare between SF6 and 02 Insulator? Explain the different schemes for cascade connection of transformers for producing very high ac voltages?
A 200 – ohm resistor, 130 millihenry inductor, and a 66 microfarad are placed in parallel across a 120 – V, 60 – Hz AC line. Calculate the following: a.) RESISTOR CURRENT b.) INDUCTOR CURRENT c.) CAPACITOR CURRENT d.) TOTAL CURRENT e.) PHASE ANGLE f.) TOTAL IMPEDANCE DRAW THE PHASOR DIAGRAM IF POSSIBLE AND ROUND OFF TO FOUR DECIMAL PLACES.
The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
A synchronous generator with a synchronous reactance of 1.15 p.u. is connected to an infinite bus whose voltage is one p.u. through an equivalent reactance of 0.15 p.u. The maximum permissible active power output is 1.2 p.u.A. Compute the excitation voltage E.B. The power output is gradually reduced to 0.7 p.u. with fixed field excitation. Find the new current and power angle δ.
A chopper circuit drives an inductive load from 390 DC supply. Given the load resistance as 8 Q, the average load current as 23 A and operating frequency is 480 Hz. When the chopper is ON, 7 V is dropped. Calculate (a) conduction period (in milliseconds) (b) blocking period of the chopper (in milliseconds) (c) duty cycle of the chopper (d) draw the ON and OFF time period waveform (ii) Draw the circuit diagram of the single phase bridge rectifier which is used in two quadrant operation (RL load) and explain its operation.
How do the capacitor and inductor support the circuit in power factor improvement?
please explain the operating principle of single phase 2S-2P PMSM based on 3D design illustration.
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
The single - phase ac voltage controller with inductive load. Plot the waveform of output voltage and voltage in each thyristor if the B = 10 %3D degree and delay angle (alpha) in both thyristor is 1- (30 degrees) 2- (90 degrees) 3- (120 degrees)
Q1) A single-phase AC voltage controller is connected to an inductive load with a resistance of 10 and load impedance angle of 45°. The input ac voltage is 230 V at 50 Hz. (a) Draw the load voltage waveforms and derive an expression for the rms load voltage. (b) Determine the maximum load voltage, maximum load current, and range of delay angie for which the load voltage does not change.