A shaft ABCD is fixed at end D and has torques acting at points A, B, and C as shown below. The bearing support between A and B allows free rotation. If we know that A = −0.382 rad, A/B = 0.358 rad, and b/c = −0.233 rad, calculate the absolute twist of the shaft at point C (oc) and enter it in rad (radians) correct to 3 significant digits below. Make sure to include the sign if it is negative noting that CCW rotations are positive and CW rotations are negative. 150 N-m A 280 N.m B 40 N-m D

A shaft ABCD is fixed at end D and has torques acting at points A, B, and C as shown below. The bearing support between A and B allows free rotation. If we know that A = −0.382 rad, A/B = 0.358 rad, and b/c = −0.233 rad, calculate the absolute twist of the shaft at point C (oc) and enter it in rad (radians) correct to 3 significant digits below. Make sure to include the sign if it is negative noting that CCW rotations are positive and CW rotations are negative. 150 N-m A 280 N.m B 40 N-m D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The shaft is fixed at ends A and B and has a positive torque T a distance of 4m from A and 8m from end B. If the angle of twist is zero and the reaction torque at A is 334N-m, what is the magnitute of applied torque T?
The axis ABCD receives a torque of 500Nm from the motor and transmits movement to other devices, by means of belts and pulleys connected at B and C. If it is known that the torques exerted on pulleys B and C are as shown In the figure, determine the minimum radius the shaft must have. You should consider that at point D of the motor there is a bearing that acts as a support for the shaft as at point A. The material of the shaft and its allowable shear stress are indicated in the drawing.Determine:to. Free-Body diagram.b. Shear force diagrams.c. Bending moment diagrams.d. Identification of the critical point of the axis.e. Calculation of the axis radius. tperm=80MPa
A steel shaft of diameter 60 mm and length 3.5 m is fixed at its ends A and B. If two torques of the same direction are applied, a 500 Nm torque at C (Im from the left end) and a 200 Nm torque at D (1m from the right end), determine the maximum internal torque in the shaft.
Shafts ab and ce are support by pillow bearing blocks as shown. Compute the angle of twist at point a. Report your answer in degrees to two decimal places. 35 in A Y bearing bearing gear c: radius 2.0 in 2 in-k gear b: shaft ab: shaft ce: radius 5.0 in b a radius 0.5 in 5 in-k radius = 0.7 in d. bearing e bearing all shafts: G = 12000 ksi 25 in 30 in
3. A cylindrical rod is composed of two pieces of different diameters. Both pieces are made of the same material. Torques are applied at points B and D, with the directions shown below. The magnitudes of the torques are Tg = 4000 in-lb, Tp = 3000 in-lb. JAC = 4 in L = 10 in. JcD = 2 in GẠC = GCD = G = 10 × 10° psi Determine the twist of point B, Ør, and the twist of point D, øp, relative to the wall at A. Note definition for + and – twist, shown to the right. Ans: = -0.25x10³ radians, øp = 2.0×10³ radians A D Tp IB Fixed to wall
Shafts ab and ce are support by pillow bearing blocks as shown. Compute the angle of twist at point a. Report your answer in degrees to two decimal places. Y le X 5 in-k bearing 25 in d bearing 30 in b 35 in bearing bearing TT C 2 2 in-k gear c: gear b: shaft ab: shaft ce: all shafts: radius 2.0 in radius 5.0 in radius 0.5 in radius= 0.7 in - G = 12000 ksi
400 mm 625 mm 1. The aluminum rod, AB (G = 27 GPa), is bonded to a brass rod BD (G = 39 GPa) and torques, TA = 800 Nm and Tg = 1600 Nm are applied as shown to the right. The diameters of AB is 36 mm and the diameter of BD is 60mm. Determine (a) the twist of point B, ø8, and (b) the twist of point A, Øa. Ans: Ø = + 3.541°, øs = -0.577° TA TB Fixed to wall
4-Determine the rotation angle between A and C, if the torque is T=0.9 N.m in point C, if G=80 GPa and diameter of all shafts are D=4 mm. (The radius of small circle are r and the bigger one are 2r) e are Coder 40 T=09N.N
In the gear system shown, the motor applies a 190 lb-ft torque to the gear at A. A torque of Tc = 392 lb-ft is removed from the shaft at gear C, and the remaining torque is removed at gear D. Assume that DA-4-in.-diameter, Dg=12-in.-diameter, L₁=56 in., and L₂-30 in. Segments (1) and (2) are solid 1.5-in.-diameter steel [G = 12200 ksi] shafts, and the bearings shown allow free rotation of the shaft. Determine: (a) the maximum shear stresses T₁, T₂ in segments (1) and (2) of the shaft. (b) the rotation angle D/B of gear D relative to gear B. Answers: (a) T₁ (b) D/B = = i ᎠᏴ ; A DA i B L₁ Tc amala ksi, T₂ = L2 i Tp D ksi.
For the steel shaft shown in Fig. Determine the torque transmitted by transverse cross sections at points A, B, and C of the shaft. 150 ft-lb 100 ft-lb 300 ft-lb
600 N-m Given: A solid aluminum shaft with 900 N-m diameter of 50 mm is loaded by torques as shown. G = 28 GPa A +Y Determine: the magnitude of twist between A and D in degrees 1100 N-m 800 N-m 2 m 3 m +X 2 m
O A. Given a homogenous shaft with length L, radius R, and modulus of rigidity G, if the internal torque along the shaft is given by the equation T(x) = 0.5x, what is the magnitude of the angle of twist at æ = L? Select one: O B L 4.JG O C. TG O D. E