A series RL circuit is not switched on. In the circuit voltage source E = 50 V DC. Resistance R = 70 and inductance L = 100.0 mH.Eki RLGive the answers to two decimal places.a) Give time constant Tau of circuitmsb) Calculate current after the switch k is closed at the moment t-17.1 ms.Ac) Calculate current after the switch k is closed at the moment 3*Tau.A

A series, RL circuit Source voltage E=50 v Inductance L=100mH Resistance R=7 ohm We need to find the…

Answered: A series RL circuit is not switched on.…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
1. A purely resistive circuit the current is leading by 90° with respect to voltage. 2. A purely inductive circuit the current is lag behind the voltage by 90°. 3. A purely capacitive circuit the current is lead by 90° with respect to the voltage. 4. A capacitor element stored magnetic energy. 5. An inductor element stored electrical energy. 6. Resistor elements consume power. 7. Angle between current and voltage is called power. 8. The power factor angle for a purely resistive is zero. 9. The power factor angle for a purely inductive load is -90°. 10. The power factor of a purely capacitive is leading.
A 22-k resistor and a 0.02-F capacitor are connected in series to a 5-V source. How long will it take the capacitor to charge to 3.4 V Select one: a. 0.501 ms b. 0.66 ms c. 0.44 ms d. 0.70 ms
If a circuit has a resistance of 3002 and a series inductance of 5002, what is the relationship between the applied circuit voltage and the circuit current? The applied voltage lags the circuit current. The phase shift between the circuit voltage and current changes with time. The applied voltage is in phase with the circuit current. The applied voltage leads the circuit cur Previous Page Next Page Page 2 of 10
elearning.adpoly.ac.ae * Question Completion Status: QUESTION 35 E-1, PC-2. Materials that have no free electrons are called? O thermistors O semicondutors O conductors O insulators QUESTION 36 E-05, PC-03. Three capacitors, 100µF, 200µF and 300µF are connected in series. What is the total capacitance? O 55µF O 600 F O 200µF O 600µF QUESTION 37 E-05, PC-02. Capacitors hold energy in the form of? O Electric field kinetic enegy magnetic field chemical energy Click Save and Submit to save and submit. Click Save All Answers to save all ansuwers.
Consider the RC circuit in Figure 2 below. Assuming the switch has been open for a long time before it is closed, fill in a table providing the current through each component and the voltage across each component immediately after the switch is closed, and a very long time after the switch is closed. Next, figure out the time constant for the circuit. (Hint: Assign currents to each branch. Set up the necessary KVL and KCL equations. Eliminate all but one variable to get an equation for just one of the currents. You shouldn’t have to solve this equation to recognize the time constant!)
Sketch even and odd for this figure
The initial rate of current rise in an RL circuit is 300 amp per sec when 120 volts is suddenly impressed. What is the inductance of the circuit?
An inductance coil consumes 500W of power at 10A and 110V and 60HZ. Determine the resistance and the inductance of the coil
Determine the loop currents Ia, I,, and Ic. 100 Ic 100 100 100 100 Ib 55V 100 V la
Very urgent. Draw the waveforms of the voltage at the load (RL) end, the voltage at the R end, the voltage at the L end and the current 1 when the switch K is turned to position 2 after a long enough time.

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS