SUBJECT IS PRINCIPLES OF REINFORCED/ PRESTRESSED CONCRETEMUST COMPLETE AND DETAILED SOLUTIONSUSED 3 DECIMALS FOR THE FINAL ANSWERSA rectangular beam has a width of 275 mm and an effective depth of 500 mm. It is reinforced with4 - 36 mm ø bars having fy = 410 MPa. If he compressive strength of the concrete is 23 MPa,determine the following:a. Location of the neutral axis from the top of the beam.b. Stress of the steel.c. Ultimate capacity of the beam?

Answered: Image /qna-images/answer/d707e9cd-a2dc-4ea7-a029-0ab62f792a64.jpg

A rectangular beam has a width of 275 mm and an effective depth of 500 mm. It is reinforced wit 4 – 36 mm ø bars having fy = 410 MPa. If he compressive strength of the concrete is 23 MPa determine the following: a. Location of the neutral axis from the top of the beam. b. Stress of the steel. c. Ultimate capacity of the beam?

A rectangular beam has a width of 275 mm and an effective depth of 500 mm. It is reinforced wit 4 – 36 mm ø bars having fy = 410 MPa. If he compressive strength of the concrete is 23 MPa determine the following: a. Location of the neutral axis from the top of the beam. b. Stress of the steel. c. Ultimate capacity of the beam?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The width and depth of a reinforced rectangular concrete beam is 400 mm and 700 mm, respectively. The effective depth is 630 mm. The material strengths are f'c=27.6 MPa and fy=414 MPa.Determine the amount of steel reinforcement at balanced condition in mm2.
A rectangular beam has the dimensions (see Figure) b = 12 in., h - 20 in, and d 17 in. and is reinforced with three No. 9 (No. 29) bars so that As - 3.00 in. The concrete compressive strength fe is 4000 psi, and the tensile strength In bending (modulus of rupture) is 475 psi. The yield point of the steel f, is 60,000 psi. Determine the concrete compression stress at the top fiber caused by a bending moment M- 10 ft-kips. 9- 6.78 in, I= 4067 in, Es= 29000000, E = 3600000 17 in. 20 in. 3 #9 bars (A, - 3.00 in.?) 3 in. -12 in- Select one: a. 390 psi b. 1390 psi c. 200 psi d. 250 psi
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars. Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MPA. 640 mm 800 mm 6 #32 C 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force
Figure 2 shows a simply supported beam and the cross section at midspan. The beam supports a uniform service (unfactored) dead load consisting of its own weight plus 1.4 kips/ft and a uniform service (unfactored) live load of 1.5 kips/ft. The concrete strength is 3500 psi, and the yield strength of the reinforcement is 60,000 psi. The concrete is normal-weight concrete. Use load (Table 5.3.1) and strength reduction factors from AC1318-14. For the midspan section shown in Fig. P4-1b, compute Mn and show that it exceeds Mu. @ (b) 3 No. 9 bars WD = 1.4 kips/ft plus weight of beam 1.5 kips/ft WL H 12 in. 20 ft TT 21.5 in. 24 in. + Figure 2.
A rectangular beam with a width of (9536/1150)-in,and effective depth of (9536/900)in is Reinforced with a single high strength steel bar that has a cross- sectional area of 0.42 in2.The bar has a normal tensile strength of 145 ksi, linear stress-strain curve to failure, and a strain at failure of 1.8 percent. The concrete strength fc= 6000 psi. Calculate the nominal flexural strength of the section.
The width and depth of a reinforced rectangular concrete beam is 400 mm and 700 mm, respectively. The effective depth is 630 mm. The material strengths are f'c=27.6 MPa and fy=414 MPa. Determine the amount of steel reinforcement in mm2 to achieve a steel train of 0.004. and the nominal flexural strength in kN.m corresponding to a steel ratio of 1.75%
A rectangular beam with width of 233 mm and overall height of 431 mm is prestressed by using a bonded (stress relieved) tendons with a specified tensile strength of prestressing tendons fpu %3D 1380 MPa. Strength of concrete is 33.1 MPa. The area of presstressed reinforcement in tension zone is 1,024 mm2 and its centroid is located 40 mm above the bottom end of the beam. The specific yield strength of prestressing tendons fpy = 1220 MPa. Compute for the ultimate moment capacity of the beam.
Reinforce Concrete: Determine the design strength of the beam. Use F'c= 21 MPa, Fy = 415 MPa, b = 400 mm, d' = 100 mm, d = 620 mm, As = 6-28 mm bars, A's = 3-28 mm bars
Q-A pre-tensioned concrete member of section 200 mm x 250 mm contains tendons of area 500 mm² at centre of gravity of the section. The prestress in the tendons is 1000 N/mm². Assuming modular ratio as 10, find the stress (N/mm2) in concrete.
Determine the required tension steel area of the T beam with given properties below. Width of flange bf = 500 mm Width of web bw = 340 mm Thickness of flange tf = 140 mm Effective depth d = 350mm Effective concretee covering d' = 75mm Compressive strength of concrete fc' = 34.5 MPa Yield stress of steel bar fy = 375 MPa Mu = 415 kN-m As = _________ mm2
SUBJECT IS PRINCIPLES OF REINFORCEDI PRESTRESSED CONCRETE MUST COMPLETE AND DETAILED SOLUTIONS USED 3 DECIMALS FOR THE FINAL ANSWERS A reinforced concrete beam has a width of 280 mm with an effective depth of 550 mm. It is reinforced with 3-32 mm Ø at the bottom. If fe' = 23 MPa, and fy = 380 MPa, determine the following: a. Balance steel ratio b. Depth of compression block. c. Moment capacity of the beam.
A spiral column with the diameter of 500 mm has the effective height of lo-4.0 m. The axial compressive strength of the concrete is f. = 14.3 N/ mm. The longitudinal steel bars are 6 22 with the yield strength of fy = 360 N/mm. The spirals are d 10@50 with the yield strength of fy = 270 N/ mm. If the concrete cover is 30 mm thick, determine the ultimate compressive capacity of the column.