A machine slide is moved by a cylinder. The motion required is as follows 1.Initially the cylinder moves against a load of 5 KN till it reaches the work piece at a speed of about 1.8 m/min 2. The speed drops to about 1 m/min as soon as the load increases to 15 KN 3. The return motion is against a load of 5 KN. A meter out circuit is used. Draw a circuit which will fulfil these requirements. Select different components you bave used in the circuit from given data. Mention the ratings of the component in case it is not available in the given data

A machine slide is moved by a cylinder. The motion required is as follows 1.Initially the cylinder moves against a load of 5 KN till it reaches the work piece at a speed of about 1.8 m/min 2. The speed drops to about 1 m/min as soon as the load increases to 15 KN 3. The return motion is against a load of 5 KN. A meter out circuit is used. Draw a circuit which will fulfil these requirements. Select different components you bave used in the circuit from given data. Mention the ratings of the component in case it is not available in the given data

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(1) In the circuit shown in the figure, the opening pressure of the relief valve is 5MPa, the setting pressure of the relief valve is 1.5mpa, and the load pressure is 1MPA when the the cylinder piston is moving. a) The pressure value at points A and B during the movement of the piston. b) The pressure value at points A and B after the piston touches the block iron. c) When the piston moves without load, what is the pressure at points A and B respectively?
Two pulleys are run by a common belt. If a 10.8 inch diameter pulley turns at 900 rpm, what is the diameter of the second pulley if it turns at 421 R.P.M.? Note: Speed is inversely proportional to diameter.
2 of 5 Review The cable is tied to the top of the ol rig, wraps around the lower pulley, then around the top pulley, and then to the motor. (Figure 1) Part A Determine the power output of the draw works motor M necessary to it the 700-lb dril pipe upward with a conatant speed of 4 ft/s Express your answer using three significant figures VO AZ vec hp Figure Submit Request Answer Next> Provide Feedback M 4n/s
solve by the concepts of statics on a paper with proper method
Please solve in statics quickly
Solve show all steps/solution as well
Draw the p-V and T-s diagrams in each problems.
Bulk loose material is to be emptied from a dump hopper. By pressing a push button P1, the dump hopper is tilted and the bulk loose materials are emptied out. By pressing another push button P2, the dump hopper is returned to its initial position. Draw the pneumatic circuit.
Pneumatics Bending Tool Problem: Sheet metal is to be bended on a pneumatically actuated bending rig. After it has been clamped the piece is initially bent by a double-acting cylinder A and subsequently bent into the finished form by cylinder B. The sequence is initiated manually by a push button. The circuit must be so constructed that each time a start signal is given a full cycle is completed. Positional Sketch: 1.0 2,0 Electro-pneumatics Sequential Circuit Problem: Initial position all cylinder are retracted. Pressing the start pushbutton makes 5 cycles. After making 5 cycles lamp is energized for 3 secs. Cycle Operation: Cylinder A extend and hold the work piece. Cylinder B extend for 5 secs. Then retract. Cylinder A retract.
pleassssse solve question 2, statics
A stepper motor drives a screw with a pitch thread of 1mm. If the motor has 100 steps per rotation, what is the resolution of the screw in mm? Note: write just the value without the unit. 0.01
3.1.1 Read through the following chronological instructions. Choose the correct figure that best matches each of the instructions below a). Attach cam shaft to the press disc by inserting the stem of the shaft into the press disc's centre hole. Press firmly. You will hear a click as the shaft snaps in place. b). Line the tabs on the motor body up with the slots on the cam disc. Insert the cam disc into the motor body. Using the two gripson disc, turn slightly clockwise until the disc clicks into position. c). Fit the shaft all the way inside the unit, until outside contours of the 2 disc line up 3.1.2 The introduction to the instructions is that you always have to unplug the biscuit and cookie maker from the outlet before assembly or disassembly of parts. Why do you think this is an important instruction