A load of 2100 N is dropped axially on a closed-coiled helical spring from a height of 240 mm. The spring has 22 coils each of mean diameter 180 mm and wire diameter is 25 mm. If the modulus of rigidity C=84000 N/mm² and amount of compression 8 = 255 mm, what is the maximum shear stress produced in the spring?

A load of 2100 N is dropped axially on a closed-coiled helical spring from a height of 240 mm. The spring has 22 coils each of mean diameter 180 mm and wire diameter is 25 mm. If the modulus of rigidity C=84000 N/mm² and amount of compression 8 = 255 mm, what is the maximum shear stress produced in the spring?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 6.2: The aluminum rod ABC (E=10.1x10° psi) (Figure 6.19), which consists of two cylindrical portions AB and BC, is to be replaced with a cylindrical steel rod DE (E=29x10° psi) of the same overall length. Determine the minimum required diameter d of the steel rod if its vertical deformation 28 kips 25 kips A D 12 in. -1.5 in. is not to exceed the deformation of the aluminum rod under the same load and if the allowable stress in the steel rod is not to exceed 24 ksi. B - 2.25 in. 18 in. E Figure 6.19
A hollow tube ABCDE constructed of Monel metal is subjected to five torques acting in the directions shown below. The tube has an outside diameter d, of 1.0 in. Given that the allowable shear stress is 12 kši, then the maximum permissible inside diameter d; of the tube is equal to T = 1000 lb-in. 800 lb-in. T = T3 = 500 Ib-in. 500 lb-in. T = T5 = 800 1b-in. B C E dz = 1.0 in. O 0.697 in O 0.908 in O 0.788 in O 0.618 in
A 200 mm 50 mm Fixed to ground B 200 mm 2000 KN X A block of rubber 50 mm thick is sandwiched between two steel plates measuring 200 mm on each side as shown. A horizontal force of 2000 kN is applied to the top plate while the bottom plate is fixed to the ground. In response to the applied force, the top plate moves 5 mm in the direction of loading. a) Determine the average shear stress between the plate and rubber. b) What is the shear strain at point A and point B relative to the x-axis?
Situation The helical spring shown is axially loaded with a compression force P equal to 5 kN. The mean diameter of the spring is 100 mm and the wire used is 10 mm as indicated in the figure. 1. What is the shear stress at A? 2. What is the shear stress at B? 3. On diameter AB, locate the point of zero stress measured from C. P = 5 kN WW P = 5 kN 100mm A 10mm B
A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 442 mm². Determine the axial stress in each bar. B 2 m O 1 m 5Q KN 1 m O E 1 m 8T KN 1 m LL
The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m. Before the load is applied, the beam hangs level. Use E = 200, 000MPa and = 11.7 um Neglect bending of the beam. m°C A=640mm2 A=320mm2 A 1.2 m 0.8 m 1.2m 54KN What is the stress of rod C if there is no change in temperature in MPa?
2.50 Before the 400-kN load is applied, the rigid platform rests on two steel bars, each of cross-sectional area 1400 mm², as shown in the figure. The cross-sectional area of the aluminum bar is 2800 mm². Compute the stress in the aluminum bar after the 400-kN load is applied. Use E = 200 GPa for steel and E = 70 GPa for alumi- num. Neglect the weight of the platform. | 400 kN 0.1 mm -b b - A B C G -1.2b- FIG. P2.49 FIG. P2.50 Steel Aluminum Steel 250 mm-
Help me
5 - An aluminum circular shaft, fixed at both ends, is loaded by torques applied at points B and C, as shown in the figure. The bar material has a shear modulus G = 85 GPa. Plot the maximum shear stress and angle of twist along the length of the shaft. B D TB 0.5m Tc 0.9m с 0.4m 40mm ↑ TB=10KN-m Tc=15kN-m
A 2 m long shaft is transmitting 90 kW at 150 RPM. The allowable shear stress in the material is 60 MPa. If the shaft is not allowed to twist more than 1°, then the diameter of the shaft required will be (Take G = 85 GPa)
Consider a fillet section subjected to a tensile force F. Knowing that the fillet section has a uniform thickness of 5 mm and a yielding stress of 250 MPa, determine the force F that initiated the yielding of the fillet section. a.1.25 kN b.2.5 kN c.4 kN F d.2 kN 40 mm 25 mm 40 mm ↓ Which of the following is FALSE regarding the equation for deformation, 8=PL/AE? A. The term AE refers to the resistance of the member against axial deformation B.It can be used even for non-prismatic members C.It can only be used to compute for the elastic axial deformation of the member D. The term P refers to the internal axial force at the section considered A rigid bar ABC is loaded and supported as shown in the figure. After the load P is applied, the deformation of bar BD, SBD 0.6mm. What is the displacement at point B? A.0.36 mm B.0.48 mm P C.0.75 mm D.1.00 mm C 0.3 m 0.3 m Which of the following statements is TRUE for a circular shaft under pure torsion? A. The angle of twist of a point on the…
1. *A propped cantilever has a 2m overhang. The beam has a load of 2W applied half way between the fixed support and the roller support and a load of W applied at the free end. What is the minimum value of W that will cause the beam to collapse? The beam has the cross-section shown below. The yield stress is 300 MPa. 75 mm 15 mm 300 mm 2W C D 15 mm 250 mm 15 mm, 2m B + 2m 2m