SIMPLE STRAIN A homogenous 900 kg bar AB is supported at either end by a cableas shown. Calculate the following:a) Weight of barb) Smallest area of each cable is the stress is not to exceed 100Mpa in bronze and 160 Mpa in steelc) Determine the Axial force of each bard) Calculate the Stress due to steele) Calculate the Stress due to bronzeSTEEL =10 MBRONZE =7MAB20 MWeight of bar = 800 x 9.81 = 7848 NOBr S 90 MPa = 90 x 10° PaOst s 120 MPa = 120 x 10° PaGiven:Given: Obr < 100 MpaOst <180 Mpa

Answered: Image /qna-images/answer/6dcffcf3-0ef0-461d-8268-e11d0e4e5811.jpg

Answered: A homogenous 900 kg bar AB is supported…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A helical spring used in an automobile suspension is having a wire diameter of 6mm and an outside diameter of 86mm. The spring has 14 active coils. If the permissible shear stress of the spring material is 345 N/mm2 and the Modulus of rigidity is 82 kN/mm2. a) Calculate the axial load in N and the deflection of the spring in mm, considering the effect of curvature. b) Calculate the value of axial load in N neglecting the effect of curvature.
AB and CD caps of the same material are tightly fitted on both ends of the 24 mm diameter AD steel bar. a) Find the pull force P that will make the total elongation of the system 0.04 mm. b) Calculate the extension amount of BC part by the force P you found. Take the elastic modulus E = 200 GPa. 36mm 24mm 36mm 48mm 72mm Smm |
A mechanism used in printing machinery consists of a helical spring which is having a wire diameter of 5mm and an outside diameter of 60mm. The spring has 12 active coils. If the permissible shear stress of the spring material is 335 N/mm2 and the Modulus of rigidity is 81 kN/mm2. a) Calculate the axial load in N and the deflection of the spring in mm, neglecting the effect of curvature. b) Calculate the value of axial load in N considering the effect of curvature.
A steel rod 8 mm in diameter is under the action of a tensile force (P) of 600 Newton. Calculate the tensile stress (s) acting in the bar. Solve for Mpa (round up to whole number)
A flat bar is 3/8 inches thick and has a centrally located drilled hole of diameter D. The bar is subjected to a 4,000 lb tensile load. Compute the maximum tensile stress adjacent to the hole. a) If the bar is 2 inches wide and D=0.25 inches b) If the bar is 2.5 inches wide and D=0.5 inches c) If the bar is 3 inches wide and D=1.00 inches Answers: a) = 15,969.5 psi (using k=2.62) b) = 13,066.7 psi (using k=2.45) c) = 12,000 psi (using k=2.25) I have no idea how to come up with these answers. Could you help me go through the process of solving for these answers step by step?
1.5 Figure 1.9 shows a circular steel rod of length 40 m and diameter 8 mm, which hangs in a mine shaft and holds an ore bucket of weight 15 kN at its lower end. Calculate the maximum axial stress, taking account of the rod weight, and assuming the weight density of rod to be 77.0 KN/m?. 40 m 8 mm 1.5 kN Figure 1.9
For the steel block (Length L = 5-meter, Width W = 1 meter, Height H = 1 meter) with compression force on its cross-sectional side of (Your Student Id)N shown in following figure; a) Calculate Stress b) Calculate Strain when its length becomes L = 4 meter after applying force. c) Calculate of modulus of Elasticity. (Hint: If your ID is 114-2020, then compression force would be 114 N)
Find the stress in members DF, FI, and HI if the cross- sectional area of each member is 800 mm?. Indicate Tension or Compression. E 3m -2m- 2m- 3m 30KN 10KN 3m K Find the following DF: Force P Stress FI: Force P Stress HI: Force P Stress C.
A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding. 24m
Figure shows a beam made from bronze subjected to a 3.5kN.m bending couple and its respective tensile properties. i) With aid of illustration, draw the deformation of the bean and locate the position where the beam experience maximum tensile stress (αmax)t and maximum compressive stress (αmax)c. Accordingly. Determine the magnitude of these two stresses. ii) Sketch the two-dimensional stress distribution acting on point A and point B over the cross-sectional area of the beam as observed from side view. Estimate the magnitude of the stresses at those two points.
A hanger rod is stressed to 0.9167 N/mm2 , when a tensile load of 18 N is acting on it as shown in fig. Find the diameter of the shaft. Hanger rod Walk away 18 N support beam Free body diagram of hanger rod
10 MPa 5 MPa 20 MPa In class exercise: Plot Mohr's circle for the given stress state

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS