A fluid with a density of 0.8 g/cm3 is being emptied from a very large tank through a small cylindrical opening with a diameter d. Use the figure below to calculate a) the diameter d of the opening if the mass flow rate at point 2 is 1.45 kg/s, and b) the flow velocity at point 3. 1. H = 4 m d = ? 3 h 1 m

A fluid with a density of 0.8 g/cm3 is being emptied from a very large tank through a small cylindrical opening with a diameter d. Use the figure below to calculate a) the diameter d of the opening if the mass flow rate at point 2 is 1.45 kg/s, and b) the flow velocity at point 3. 1. H = 4 m d = ? 3 h 1 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Fluid is moving at rate of 3m/s in a chamber of a 12inch positive displacement flow meter, if the density of the fluid is 4.5kg/m³ and has a mass flow rate of 8kg/s, what is the maximum volume capacity of the chamber?
An incompressible fluid (density 1000kg/m3) is flowing through a pipe with a constriction. The pipe is on an angle of 30 degrees with the narrow section at at distance of 10m from the wide section and lower that the wide section . The speed of the fluid in the wide section is 2m/s and 10m/s in the narrow section, I f the pressure in the wide section in 250 kPa. What is the pressure of the fluid in the narrow section ?
fluid2.pdf -> Example 2 • Water is flowing from hole 1cm radius at the bottom of a closed cylindrical container of 2m diameter. If the height of the water in the container is 2 m and the pressure over the surface of water is 3 atm. calculate how much time it took until the container became empty? P.
Simulation of laminar gas flow in the pipe with Ansys Fluent Task: 1. Calculate velocity distribution in y axis at inlet and outlet of the pipe. Submit it as a chart. 2. Calculate velocity distribution over the pipe length. Submit it as a chart. Figure. pipe geometry L, m = 16 R, m= 0.15 Inlet velocity, m/s= 0.08 Gas= Oxygen Need proper solution like pdf file, don't need steps by steps. If you can can do it through ansys fluent. Write proper solution on word file or pdf.
Directions: In any clean sheet of paper, write your name, solve the problem and show your solution. Box your final answer. Take a picture of it and upload it here (image/pdf). 1) Between two sections in a vessel, a fluid moves in a steady flow manner. At entrance: A1=20 m2, P1=1300 kgm/m3. At exit: A2-10 m2, 02=0.00125 m /kg, Ü2=3 m/min. Determine the following: a) m, in kg/min b) Ủz in m/min
A) Figure (2) shows the velocity distribution for flow of water between two parallel plates. Velocity profile: u = 10(0.01y - y²). Figure (2) Find: 1) The value of Y. 2) Shear stress at the wall. 3) Shear stress at 20μm from the wall. 4) Location of zero shear stress 5) Location of maximum velocity. B) The laminar flow velocity profile in pipe for Newtonian fluid is given by: Ux = 2ū i [1 − (²7)²], where u, is point velocity at any radial position (r). Use the above relation to find the expression for velocity gradient at the pipe wall. water at 20°C
A gas flows through a square conduit, at the entrance the conduit sides are 10 cm, the velocity is 7.55 m/s, and the gas mass density is 1.09 kg/cu. m. At the exit, the conduits sides are 25 cm, and the velocity of flow is 2.02 m/s. Find the density of the gas at the exit section considering that the gas is compressible a. 0.6598 kg/cu. m b. 0.6851 kg/cu. m c. 0.6518 kg/cu. m d. 0.6185 kg/cu. m
A/ A tank fill by the liquid and partially immersed a very long vertical tube in it. The tube has the radius R and rotating at o radians per second clockwise. Find the steady state velocity and pressure profiles in cylındrical coordinates.
QA An incompressible fluid (kinematic viscosity, 7.4 x10-7 m2/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is (a) 0.651 x 10-3 (c) 6.51 (b) 0.651 (d) 0.651 x 103
2) Consider steady state, laminar flow of a fluid in the -y direction between two parallel and vertical plates with a distance of h. Plate A is stationary. Plate B moves in -y direction, as shown below. Derive an equation for the velocity profile. Hint: Choose a volume element and state all your assumptions. 5m/s A B Direction of flow
Air is accelerated in a nozzle. The mass flow rate in kg/s and the exit area in cm? of the nozzle are to be determined. (Express your answer: mass flow rate must be rounded off to three decimal places and the area in one decimal place.) V, - 20 m's 4- 60 cm" AIR V, = 150 m's Answer:
Problem (3) Find the rate of change of h(t) (mm/s) if water is the fluid at all locations. Use V₁ = 7.1 m/s and Q = 1000 L/min. m₂ = 10 kg/s 4 cm dia. V₁ Answer: 120 cm h(t) 8