A diverging tube discharges water from reservoir at a depth of 10 m below the water surface. The diameter of the tube gradually increases from 150 mm at the throat to 225 mm at the outlet. Neglecting friction, determine the maximum possible rate of discharge through this tube. Water 10 m 150 mm Ø 225 mm 0 Activate Go to Sett

A diverging tube discharges water from reservoir at a depth of 10 m below the water surface. The diameter of the tube gradually increases from 150 mm at the throat to 225 mm at the outlet. Neglecting friction, determine the maximum possible rate of discharge through this tube. Water 10 m 150 mm Ø 225 mm 0 Activate Go to Sett

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Length and dia. Of pipe 1 are 2000m and 1m while the second pipe is 2000m and dia. Of 0.8m .Find the rate flow of each pipe if the total flow rate in the main pipe is 0.3 m3/s. the coefficient friction of each pipe is same and equal to 0.05. Ans.Q1= 1.906 m3/s , Q2=1.094m3/s Ex. A pipe of dia.=20cm and length 2000m is connects two reservoir having difference of water levels as 20m determine the discharge through pipe. If an additional pipe of diameter 20cm and length 1200 m is attached to the last 1200m length of the existing pipe, find the increase in the discharge. f=0.015 neglect minor losses. Ans.Q= 0.0254 m3/s , increase to discharge 0.0088m3/s Ex. Pipe of L=4000m and dia.=0.6m as shown in fig. At a distance of 1000m from the upper reservoir , a small pipe is connected to the pipe line. The water can be taken from the small pipe. Find discharge to the lower reservoir a- No water is taken from the small pipe b-100 liter/sec of water is taken from small pipe. f30.005 neglect minor…
Determine the discharge through three new cast-iron pipe connected in series, having diameters of 250mm, 200mm, 150mm and lengths of 600m, 360m and 270m respectively, When the total friction loss not including the minor losses is 5.0 m. Assume f=0.024 for all pipes.( hint: apply H= f.L.V²/( D.2.g)₁ + f.L.V²/( D.2.g)₂ + f.L.V²/( D.2.g)₃ and Q1=Q2=Q3 where Q=A.V ).
FOR THE PIPE NETWORKS SHOWN, THE FLOW OF WATER FROM A TO THE FIRST JUNCTION IS 2 CUBIC FEET PER SECOND. ASSUMIN ALL PIPES HAVE A FRICTION FACTOR OF 0.020 A. DETERMINE THE HEAD LOSS IN FEET IN PIPE 1(ROUND OFF FINAL ANSWER TO TWO DECIMAL PLACES) B. B. DETERMINE THE HEAD LOSS IN PIPE 5 ROUND OFF FINAL ANSWER TO TWO DECIMAL PLACES)
Determine the corrected flow in pipe BE of the pipe network shown. Use f=0.012 for all pipes and initially assume equal flow in pipes AB and AE. 0.6 m/s A 300m B 300m c 0.4 m/s 300mm 424m 300mm 250mm 300m 250mm E 300m D 300m 250mm 0.2 m/s 250mm Select one: O a. 14.16 liters per second O b. 152.25 liters per second O c. 92.75 liters per second O d. 67.85 liters per second
The value of (NPSH) for a pump is given by the manufacturer as 10 ft. Water is being pumped from a reservoir at min atmospheric pressure at a rate of 30 ft /s to a tank at atmospheric pressure. The water level in the reservoir is 5 ft below the pump. If the total head loss in the suction pipe is 5 ft, is the pump safe from cavitation effects? If a 2-in schedule 40 pipe of 150 m length was used downstream of the pump, what is the power delivered to the fluid? You may assume that the friction factor in the pipe is equal to 0.004.
A venturi-meter having an entrance diameter of 300 mm and throat diameter 200 mm is used to measure the volume of a water flowing through a pipe. The coefficient of discharge is 0,96. The reading in the venturi-meter head is 175 mm of water. Determine the volumetric quantity of water flowing.
Q2 Q1 u (poise) Sp. Gr. D (mm) L (m) Q3 Q (Lit/s) H E (mm) 0.02 0.8 50 500 0.19 18 2
04: Three pipes of diameters 300 mm, 200 mm and 400 mm and lengths 450 m, 255 m and 315 m, respectively, are connected in series. The difference in water surface levels in two tanks is 18 m. Determine the rate of water flow if coefficients of friction are 0.0075, 0.0078 and 0.0072, respectively, considering: (a) with minor losses, (b) without (neglecting) ‘minor losses.
Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft^3/s. Hint: You need to use the Tioga table and K value for minor losses. Z₂ = 107 ft Reservoir B 90° regular screwed elbow Pump Z₁ = 53 ft Reservoir A A) H=51+25.98(Q^2) B) H=54+24.98(Q^2) ⒸH=54+25.98(Q^2) ⠀
Determine the NPSH available for the system shown. The pump takes water at 30 ° C. The system is installed at sea level. The pump is at 2 m above the water level. The pipe measures 6 m and the diameter of 5 cm. The tubing has a sharp edge entry and the elbow is 90 ° threaded. The flow that the pump moves is 90 liters per minute. The material of the tubing is galvanized iron.
Reservoirs A, B and C are located atop a hill as shown. Use the formula for headloss: hf = 0.083f Q² with f= 0.011 for all pipes. Calculate the flow rates in the three pipes. EL 30 A EL 25 B L = 1200m D = 300mm %3D EL 15 L2 = 900m D2 = 200mm %3D B L3 = 1500m D3 = 150mm %3D
A 250 mm diameter and 3 km long straight pipe connects two reservoirs of water surface elevations 135.00 m and 60.00 m. A 1.5 km long, 300 mm diameter pipe is laid parallel to 250 mm diameter pipe from its mid-point to the lower reservoir. Neglecting minor losses and assuming friction factor as 0.02 for both the pipes. Find the original discharge and the increased discharge