a) Design a cantilever beam with a span length of 2.6m. The beam is exposed to 34kN/m dead load and 20kN/m live load. Height, width and concrete cover of the beam are 69cm and 30cm and 4cm respectively. Use C35 concrete and S420 steel and choose Ø16 bars. b) Calculate the spacing between the bars and indicate whether the bars can be placed as a single layer or not. Assume 2.1 cm concrete cover on the sides, 25mm maximum aggregate size and Ø10 stirrups. c) Draw the cross-section of the beam showing all reinforcement and dimensions. Use Ø12 hanger bars if required.

a) Design a cantilever beam with a span length of 2.6m. The beam is exposed to 34kN/m dead load and 20kN/m live load. Height, width and concrete cover of the beam are 69cm and 30cm and 4cm respectively. Use C35 concrete and S420 steel and choose Ø16 bars. b) Calculate the spacing between the bars and indicate whether the bars can be placed as a single layer or not. Assume 2.1 cm concrete cover on the sides, 25mm maximum aggregate size and Ø10 stirrups. c) Draw the cross-section of the beam showing all reinforcement and dimensions. Use Ø12 hanger bars if required.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

concrete floor slab 100 mm thick is cast monolithic with concrete beam 2.0 m on centers. The beams have a span of 4.2 m and have a web width of 250 mm, and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm bars in two rows with 25 mm vertical clear spacing. Use material strength f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry; a) effective flange width of an interior beam in mm b) depth of uniform stress block at ultimate stage in mm ( round of to nearest whole number) c) tensile steel strain compatible with concrete strain if 0.003 ( round if 3 decimal places)
O Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu:= 30-MPa fy:= 450-MPa b:= 280-mm d:= 510-mm A, 2410-mm d':= 50-mm A's:= 628-mm² b A', d'
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.2 m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-∅25 mm bars in two rows with 25 mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places.
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.2 m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm diameters bars in two rows with 25 mm vertical clear spacing. Use material strengths f'c = 21 MPa and fy = 415 Mpa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm Depth of uniform stress block at ultimate stage in mm to the nearest whole number Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places
Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu= 30-MPa fy:= 450-MPa b:= 280 mm d:= 510 mm d':= 50-mm 2 A, 2410-mm A's:= 628-mm 2 b A', Hi As
3) A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.2 m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-∅25 mm bars in two rows with 25 mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = ___________ Depth of uniform stress block at ultimate stage in mm to the nearest whole number = ___________ Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places = __________
a concrete floor slab 100mm thick is cast monotholic with concrete beams 2.0 m on centers. the beams have a span of 4.0m, web width of 259 mm and overall depth of 50 mm. the tensile reinforcement consists of 6-⌀20 mm bars in two rows with 25mm vertical clear spacing. use material strengths f'c=21MPa and fy=415MPa. calculate the ff considering a T-geometry: 1. effective flange width of an interior beam in mm 2. depth of uniform stress block at ultimate stage in mm to the nearest whole number 3. tensile steel strain compatible strain of 0.003
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f'c = 21 Pa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars Determine the limiting tensile steel ratio for a tension controlled condition in positive or negative bending with the given material strengths.
A reinforced concrete beam has a width of 300 mm and an effective depth of 618 mm. Compressive reinforcement will be placed at d' = 60 mm, f'c = 28 MPa and fy = 415 MPa. Use Ø = 0.9 for flexure and load combination of U= 1.2DL + 1.6LL. Reference: NSCP 2015. a. Calculate the steel ratio for a balanced section, phal- b. Calculate the maximum steel ratio for a tension-controlled section, pmax. d. c. If the beam is to support a bending moment of 240 kN-m from dead load and 195 kN-m from live load, determine the required design flexural strength of the section. If the beam is to support a bending moment of 240 kN-m from dead load and 195 kN-m from live load, determine the number of 28 mmø bars required as tension reinforcement.
A beam cast monolithically has the following properties: bf=1200mm, t or hf = 110mm, bw=380mm and h=800mm. It is reinforced with 10D32mm grade 420MPa bars. Concrete strength is assumed to be 27.5MPa and the centroid of tension reinforcement is located 665mm from the outermost compression fiber. i.Determine the design strength in kN-m.
Q-A pre-tensioned concrete member of section 200 mm x 250 mm contains tendons of area 500 mm² at centre of gravity of the section. The prestress in the tendons is 1000 N/mm². Assuming modular ratio as 10, find the stress (N/mm2) in concrete.
A rectangular beam has the dimensions (see Figure) b = 12 in, h= 20 in, and d= 17 in. and is reinforced with three No. 9 (No. 29) bars so that As - 3.00 in?. The concrete compressive strength fe is 4000 psi, and the tensile strength in bending (modulus of rupture) is 475 psi. The yield point of the steel f, is 60,000 psi. Determine the stress in the steel caused by a bending moment M = 10 ft-kips. 9 - 6.78 in, I- 4067 in, Es = 29000000, E - 3600000 L17 in. 20 in. 3 #9 bars (A, - 3.00 in.) 3 in. -12 in.- Select one: a. 2525 psi b. 2412 psi C. 2615 psi d. 2817 psi