A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 212 mm and a wall thickness of 9 mm. Segment (2) has an outside diameter of 139 mm and a wall thickness of 11 mm. The shaft is subjected to torques TB = 47 kN-m and Tc = 24 kN-m, which act in the directions shown. Determine the maximum shear stress magnitudes 7₁, 72 in each shaft segment.

A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 212 mm and a wall thickness of 9 mm. Segment (2) has an outside diameter of 139 mm and a wall thickness of 11 mm. The shaft is subjected to torques TB = 47 kN-m and Tc = 24 kN-m, which act in the directions shown. Determine the maximum shear stress magnitudes 7₁, 72 in each shaft segment.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The compound shaft carries the two torques shown. The shear moduli are 28 GPa for aluminum, 83 GPa for steel, and 35 Gpa for bronze. If T = 1168.7 Nm, U = 4515 Nm, x = 3.01 m, y = 2.36 m, z = 1.35 m, d = 90 mm, and e = 83 mm, find the angle of rotation of the free end of the shaft. Round off the final answer to two decimal places. U T Aluminum Steel Bronze
The aluminum shaft, composed of three segments is fastened to rigid supports as A and D. Calculate the maximum shear stress in each segment when the two torques are applied. A 400 N-m 850 N-m L=1.4 m 30 mm diameter B L=2.4 m 50 mm diameter L-1.9 m 30 mm diameter
A compound shaft consists of an outside tube (1) and an inner tube (2) that are fully connected together. Determine the maximum allowable torque that could be applied to the compound shaft if the allowable shear stress in the outer shaft is Tall, 1 = 83 MPa, and the allowable shear stress in the inner shaft is Tall,2= 62 MPa.[G₁ = 32 GPa, G₂ = 22 GPa, d₁ = 101 mm, d₂ = 83 mm, d3= 56 mm] Answer: dz d₂ d₁ Tube (1) Tube (2) kN.m
The copper pipe has an outer diameter of 2.5 in. and an inner diameter of 2.25 in. It is tightly secured to the wall at C and a uniformly distributed torque is applied to it as shown.(Figure 1) Points A and B lie on the pipe's outer surface. Figure C B |--M 2 ft V 150 lb-ft/ft. TIM A 2 ft V -- < 1 of 1 Determine the shear stress at point A. Express your answer to three significant figures and include appropriate units. TA = ΤΑ Submit Part B O — μA 4 TB = Value Units Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining μA P Determine the shear stress at point B. Express your answer to three significant figures and include appropriate units. Value Units ? www ? Submit Previous Answers Request Answer
A compound shaft consists of an outside tube (1) and an inner tub (2) that are fully connected together. Determine the maximun allowable torque that could be applied to the compound shaft if the allowable shear stress in the outer shaft is Tall, 1 = 89 MPa, and the allowable shear stress in the inner shaft is Tall,2 = 62 MPa.[G₁: 39 GPa, G₂ = 16 GPa, d₁ = 102 mm, d₂ = 87 mm, d3 = 55 mm] Tube (1) Tube (2) Answer: d3 d₂ d₁ Tube (1) Tube (2) kN.m
A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 216 mm and a wall thickness of 10 mm. Segment (2) has an outside diameter of 124 mm and a wall thickness of 14 mm. The shaft is subjected to torques Tg = 34 kN-m and Tc = 15 kN-m, which act in the directions shown. Determine the maximum shear stress magnitude in segment (2). (1) O 62.5 MPa O 80.7 MPa O 85.3 MPa O 73.5 MPa O 66.2 MPa
A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an allowable shear stress of 59 MPa. Segment (2) is a solid aluminum shaft with an allowable shear stress of 84 MPa. If a torque of Tc=29400 N-m is applied at C, determine the minimum required diameter of the brass shaft d₁ and the aluminum shaft d2. Tc Answers: d₁ = d₂ = i (2) B A mm mm
The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the torques 2T and 3T at points A and B, respectively. If tallow = 35 MPa and (fA/C)allow =2o, determine the maximum permissible value of the torque T. Use the table given below and your student ID to find the values of L1, L2, and D. Student ID L1 (m) L2 (m) D (mm) 1131731 1 0.6 78
Four pulleys are attached to the 50-mm-diameter aluminum shaft. If torques are applied to the pulleys as shown in the figure, determine the angle of rotation of pulley D relative to pulley A. Use G = 28 GPa for aluminum. 600 N m 900 N m 1100 N m 800 N m 2 m 2 m 3 m
The dimensions of the cross section of an airplane fuselage are shown in figure 1. If the fuselage is subjected to a torque of 8 MN-m, determine the maximum shear stress and twist per unit length of the fuselage. The thickness of the wall is 3 mm. Take the G for curved walls as 25000 N/mm and for the straight walls as 27500 N/mm². 09 m 1.35 m 09 m Figure 1
The shaft consists of three concentric tubes, each made from the same material and having inner and outer radii as given below. Length of shaft is 2m. One end is fixed to the wall and to the other end a disc is attached. If a torque of T =800 N.m is applied at the disc end, determine the maximum shear stress in the shaft. 1. Inner tube: r; = 20mm, r, = 25 mm 2. Center tube: r; = 26 mm, r. = 30 mm 3. Outer tube: r = 32mm, r, = 38mm
Four pulleys are attached to the 50-mm-diameter aluminum shaft. If torques are applied to the pulleys as shown in the figure, determine the angle of rotation of pulley D relative to pulley A. Use G = 28 GPa for aluminum.