Thescrew clamp shown in the figure applies a P = 500 N pressing force to the woodenblocks between the jaws. In this case;a) Calculate the greatest tensile and compressive stresses occurring in the section a-a shownin the figure.b) Show the distribution of normal stresses across the section height. (draw)c) Since the clamp material has tensile strength (apull) safety = 50MPA and compressionsafe stress (opress) safety = 80MPA, what is the great compressive load (P) that can beapplied without damaging the a-a section?%3D%3D(Please solve in detail and according to engineering rules.)Material mechanicsSectional view a-a- 20mmT.183mm40mm

Answered: Image /qna-images/answer/c31a96c5-84c5-43d5-903e-143af9cc3871.jpg

a) Calculate the greatest tensile and compressive stresses occurring in the section a-a shown in the figure. Mww w b) Show the distribution of normal stresses across the section height. (draw) c) Since the clamr material has tensile strength (apull) safety = 50MPA and compression safe stress (opress) safety = 80MPa, what is the great compressive load (P) that can be applied without damaging the a-a section? %3D

a) Calculate the greatest tensile and compressive stresses occurring in the section a-a shown in the figure. Mww w b) Show the distribution of normal stresses across the section height. (draw) c) Since the clamr material has tensile strength (apull) safety = 50MPA and compression safe stress (opress) safety = 80MPa, what is the great compressive load (P) that can be applied without damaging the a-a section? %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the assembly of the bronze tube and steel bolt, the pitch of the threads is p = 1/32 in.; the cross-sectional area of the bronze tube is 1.5 in? and of steel bolt is 4 in?. the nut is turned until there is a compressive stress of 4,000 psi in the bronze tube. Find the stresses (psi) if the nut is given one additional turn. How many turns of the nut will reduce these stresses to zero? Use Epr = 12 x 106 psi and E = 29 x 10° psi. L= 40 in.
GIVEN: Solid alumınum bar shown: 4 in. by4 in. E = 10 x 10° psi oy = 36 ksi 4000 2000 1b 4000 16 B 12' REQ’D: A) Load in each section of the bar (state whether C or T) PAB = Pac PCD = B) Maximum axial stress in the bar. In which section does this occur? C) Final length of the bar
The pin in the image shown below must transfer an axial tension force of 12.7 kN. Calculate the minimum pin diameter. Use Shear stress-D0.4"Yield strength. Assume material is 1020 hot-rolled steel. * P2 Shear Planes Pin
The assembly consists of a bronze tube and a threaded steel bolt. The pitch of the thread is 1/32 in. (one turn of the nut advances it 1/32 in.). The cross-sectional areas are 1.5 in? for the tube and 0.75 in? for the bolt. The nut is turned until there is a compressive stress of 4000 psi in the tube. Find the stresses in the bolt and the tube if the nut is given one additional turn. Use E = 12 x 10° psi for bronze and E = 29 x 10° psi for steel. Bronze tube 40 in.-
2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions indicated. Find the f a) The max Compressive stress in the system P-60 kN Aluminum A=400 mm b) The max Tensile stress in the system P-60 kN Steel A = 500 mm² Bronze A-200 mm² 4P 2.5 m 1.5 m 2.0 m 2P
A bolted connection between a vertical column and a diagonal brace is shown in the figure below. The connection consists of three 5/8-in. bolts that join two 1/4-in. end plates welded to the brace and a 5/8-in. gusset plate welded to the column. The compressive load P carried by the brace equals 8.0 k. Determine the following quantities: (a) The average shear stress (τ)ave in the bolts, and (b) the average bearing stress (σ)b between the gusset plate and the bolts. (Disregard friction between the plates.)
4.) A 150 x 90 x 12 angular section is welded to a gusset plate as shown in the figure. The angle is A36 steel with FY=248 MPa. The weld is E 80 electrode with Fu = 550 MPa. The allowable tensile stress for the angle is 0.6Fy and the allowable shear stress for the weld is 0.3Fu. The Area of the angular section is 2751 sq.mm. with y=51mm. CS 56 Which of the following most nearly gives the design force P? a.) 400,365.9 N b.) 409,348.8 N c.) 412,793.5 N d.) 420,366.6 N 5.) A W350 x 90 steel is used as a simply supported beam 8m long. The beam carries three equal concentrated loads at every quarter points. It also carries a uniform dead load o 5 kn/m (including its own weight) and a uniform live load of 7.20 kn/m. Properties of W 350 x 90 steel: bf = 250 mm The allowable bending stress is 0.66Fy. The allowable shear stress is 0.40Fy. The allowable deflection is L/360. Use Fx=248 Mpa and E=200 Gpa. tf = 16.40 mm V d = 350 mm Determine the maximum value of each concentrated load based on…
The wooden beam shown is made by gluing together planks as shown. 8 kN/m Glue 80 mm A B 80 mm - NA 6 m 80 mm 160 mm Determine the maximum shear stress in the glue in kPa. (2 decimals)
The light rigid bar ABCD shown Is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. E200 CPa E1m 2.0 m 0.6m 1.5 m VP-20 KN Aluminum E-70 GPa A=900mm2 L-1.5 m What is the axial stress at steel rod in MPa?
Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 0.8 m 50 kN/m B -2.4 m- 0.8 m For the selected design, determine the actual value of Om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.
The steel shafts are connected together using a fillet weld as shown in the figure below. (Figure 1) Figure ▾ art A Tavg for Part A for Part 12 mm Value T= 60 N-m 50 mm- Determine the average shear stress in the weld along section a-a if the torque applied to the shafts is T = 63 N-m. Note: The critical section where the weld fails is along section a-s. Express your answer to three significant figures and include the appropriate units. Units 12 mm 1 12 mm 12 mm a do for Part 1 of 1 redo for Part A reset for Part A keyboard shortcuts for Part A help for Part A
A bracket has been loaded as shown in figure. Compute the top and bottom fibre stress at section AB