A cable is enacting a force, F, on a built-in hook at an angle 8 as shown in the figure. Determine the displacement of the point at which the force acts, in the direction of the cable if the shaft of the hook has a length L, radius r and elastic modulus E. Ignore the deformation of the circular hook. AT

A cable is enacting a force, F, on a built-in hook at an angle 8 as shown in the figure. Determine the displacement of the point at which the force acts, in the direction of the cable if the shaft of the hook has a length L, radius r and elastic modulus E. Ignore the deformation of the circular hook. AT

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.5.10P: Solve the preceding problem (W 250 × 44.8) if the resultant force P equals 110 kN and E = 200 GPa.

See similar textbooks

Similar questions

Determine the intensity and position of the resultant R lf two forces F1 and F3 and torque M that acts on the metal profile given as in the figure,if: F1= 2kN a=2,10m F2= 5kN b=2,10m M=24kNm c=3,10m
Problem 2 The series of bars shown have their diameters from left to right decreasing by 3 mm, and lengths increasing correspondingly by 0.3 m. If the leftmost member has a diameter and length of 28 mm, 1.8 m, respectively, determine the nodal displacements, member forces and the value of P if the node where P acts undergoes a rightward displacement of 4.5 mm. E=180 GPa for all members. Use your calculator. 90 N/mm 45 N/mm 60 N/mm 30 KN -50 KN
As the electric motor rotates at a constant speed, it applies a torque of 500 Nm to the ABCD shaft. Determine the torsion angle between B and C since G = 27 GPa and the torques shown in the figure are applied to the pulleys B and C.
YA 37 N-m The braket shown in figure is subjected to three forces and one couple as Shown in figure. Find the result ant R of the force System and the of it's line of action with the lines AB and BC. 120N 600N 9. 30 200 mm 50 mm V1OON points of intersedion R = 446.86 NoO =26:58s %3D d=0.0447m =44.7 mm « a = 0. ol m = lomm 6 %3D b=0.05 m = 50 mm · loomm
The shaft is supported at its ends two bearings A and B and is subjected to the forces applied to the pulleys fixed to the shaft. (Figure 1) The T₁ = 410-N forces act in the -z direction and the 200-N and 80-N forces act in the +y direction. The journal bearings at A and B exert only y and components of force on the shaft. Figure 200 mm 300 mm 150 mm, 150 mm 200 mm 400 mm B 200 N 80 N 80 N 200 N < 1 of 1 Determine the resultant normal force on the cross section at C Express your answer to three significant figures and include appropriate units. Nc= Submit Part B (Vc)y= Submit Part C Value Determine the resultant shear force in the y direction on the cross section at C Express your answer to three significant figures and include appropriate units. (Vc)= = Request Answer 4 ▬▬ μÀ 4 Value Request Answer μÃ → ⒸIE ? Value Units Determine the resultant shear force in the direction on the cross section at C Express your answer to three significant figures and include appropriate units. Ć IE ?…
5:55 PM ~ 3 m 20 kN [Ε B -2 m--2 m--2 m--2 m--2 m--2 m- Member AB is a: N D 30 kN 40 kN O Tensile Member O Compressive Member O Zero-Force Member O Not a Member ( 50 ) l اس. © 2 F G
Consider the joint steel bars below. If 50,000 lb force is applied at point A, determine the displacement of point A along x and y axis, and the normal reactions in the supports. Assume EST = 29 x 10° psi. Area of steel bar is 2.5 in². 50 000 16 50 15 in A 10 in 10 in 15 in
Q3 The steel shaft, shown in the figure, is made from two segments: AC has a diameter of 30 mm and CB has a diameter of 55 mm. If it is fixed at its ends A and B, determine the magnitude of the applied torque T if the reaction at A is 75 N.m. Use G= 75 GPa. %3D 50 mm 25 mm T A B 1.5 m 0.75 m 1 m
Forces of F1=15 kN in the z direction from the B point, F2=10 kN in the z direction from the C point and F3=10 kN in the y direction act on the arm in the figure. The lengths of the arm are also given as L1=0.15 m and L2=0.16 m. The radius r in the a-a section taken over the arm is r=0.2 m and it is desired to determine the stress state at point A. The shear modulus of the sleeve material is G=65 Gpa. According to this; WRITE YOUR RESULTS IN THE BOXES WITHOUT THE UNITS IN kPa. a) Find the shear stress due to the shear force at point A. Response b) Find the shear stress due to the torsional moment at point A. Response c) Find the total shear stress at point A. Response d) Find the normal stress due to the normal force at point A. Response e) Find the normal stress due to the bending moment at point A. Response f) Find the total normal stress at point A. Response
The uniform 44 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional area of the wire is 178.5 mm2. Assuming bar BC to be rigid, find the vertical displacement of B due to the weight of the bar. Use E = 71 GPa for aluminum. Anwer must be in mm.
CDEFGH is plate with a circular hole in it and has a unit weight p = 2 kN/m². If the initial length of the spring is 1m, find the stretched length of the spring attached at C to the given system. The stiffness of the spring id k=50 kN/m. bwwwww.. 2 m H 0 D X 2 m 2 m G 2 m F E 3m 1m
A force P of 70 N is applied by a rider to the front hand brake of a bicycle(Pis the resultant of an evenly distributed pressure). As the hand brakepivots at A. a tension T develops in the 460-mm Ions; brake cable (Ae=1.075 mm²), which elongates by δ 6=0.214 mm. Find the normal stress 8and strain e in the brake cable.Brake cable, L = 460 mmHand brake pivot A