A 7-meter tall post is sunk firmly into the ground. Two tension forces are applied to the top of the post as shown in the diagram below. Tension 1 has magnitude of 6 Newtons and acts horizontally. Tension 2 has a magnitude of 7 Newtons and acts 34 degrees below horizontal. What is the expected reaction moment, in N-m, at the base of the post at A? Remember positive moments act counterclockwise and negative moments act clockwise. T₁ 7m A Ө T₂

A 7-meter tall post is sunk firmly into the ground. Two tension forces are applied to the top of the post as shown in the diagram below. Tension 1 has magnitude of 6 Newtons and acts horizontally. Tension 2 has a magnitude of 7 Newtons and acts 34 degrees below horizontal. What is the expected reaction moment, in N-m, at the base of the post at A? Remember positive moments act counterclockwise and negative moments act clockwise. T₁ 7m A Ө T₂

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

6. The uniform beam is supported at its ends by two springs A and B, each having the same stiffness k. When nothing is supported on the beam, it has a period of vertical vibration of 0.83 s. If a 50-kg mass is placed at its center, the period of vertical vibration is 1.52 s. Compute the stiffness of each spring and the mass of the beam. A B www
Experiment: A and B are the two supports on a 10-meter-long beam. The beam is fastened at Support A and supported by a roller at Support B, and it is centred by a 10kN elephant. A free-body diagram (FBD), as well as a shear and bending moment diagram, should be created for this system. You may discuss about the results and explain the stress in the beam. Explain the principle of statics and aim of this experiment.
The torques shown are exerted on pulleys A and B which are attached to solid circular shafts AB and BC. In order to reduce to total mass of the assembly, detemine the smallest diameter of shaft BC for which the largest shearing stress in the assembly is not increased. TA = 300 N m 30 min B TH = 400 N- m 46 nn
Problem 314 The steel shaft shown in Fig. P-314 rotates at 4 Hz with 35 kW taken off at A, 20 kW removed at B, and 55 kW applied at C. Using G = 83 GPa, find the maximum shearing stress and the angle of rotation of gear A relative to gear C. A 55 mm >> 4 m Figure P-314 B 65 mm 2 m C
In the Figure 6, the absolute force value in the bar AB is (in kN): Figure 6: 5 m, 5 m 5 m y X A 20 kN B الاختيارات 8.55 O 10.55 O 11.55 O 9.55 O
A 10 m long beam has 2 supports at point A and B. The beam is pinned at Support A and supported by a roller at Support B. It is carrying a car (mass of car= 1660kg) at middle of the beam. Draw the free-body diagram (FBD); construct the shear and bending moment diagram for this system. Discuss the results and explain the stress of this beam. Provide your opinion on the effect of the beam when the centroid of the vehicle is shifted to 3m away from Support B. Using equilibrium i.e. force and moment equilibrium must be satisfied for each component, determine the forces or/and moments. List all assumptions that are
Experiment: A and B are the two supports on a 10-meter-long beam. The beam is fastened at Support A and supported by a roller at Support B, and it is centred by a 10kN elephant. A free-body diagram (FBD), as well as a shear and bending moment diagram, should be created for this system. You may discuss about the results and explain the stress in the beam. In words, explain the principle of statics and aim of this experiment.
QUESTION 4 A shaft AB is attached to the beam CDFH as shown in fig Q4 below. A torque of 200 kNm is applied to the end B of the shaft. Determine the rotation of section B. The shaft and beam are made of an aluminium alloy for which E= 720 GPa and G = 27 GPa, Neglect the strain energy of the hub DF. IC 400 mm 200 mm- 40.0 mm D 60.0 mm 400 mm 800 mm HO H 30.0 mm T= 2.00 kN.m
The figure shown is a beam subjected to varying loadings and a point load.a) Determine the magnitude and direction of the single equivalent force to the forcing systemshown. Specify its location on the beam from point B.b) Calculate for the support reactions at A and B.
Problem 2: For the shown beam, 40 N 150 N 250 N knowing that distance d = 1.0 m: a. Calculate the reactions at the supports on the opposite beam. ......
Mechanics of Deformable Bodies 80 N 200 mm 300 mm B The pipe shown in the figure has an inner diameter of 80 mm and an outer diameter of 100 mm. If its end is tightened against the support at A using a torque wrench at B, determine the shear stress developed in the material at the inner and outer walls along the central portion of the pipe when the 80-N forces are applied to the wrench. с 80 N
Problem 1: The figure shown is a beam subjected to varying loadings and a point load. a) Determine the magnitude and direction of the single equivalent force to the forci shown. Specify its location on the beam from point B. b) Calculate for the support reactions at A and R Fi 17kN 4kN/: 7.9 kN/m -5 m 6.7 m 2.8kn