A 36-mm-diameter solid steel shaft supports loads PA = 1,400 N and Pc = 2,100 N as shown. Assume L₁ = 100 mm, L₂ = 200 mm, and L3 = 150 mm. The bearing at B can be idealized as a roller support and the bearing at D can be idealized as a pin support. The moment of inertia of the shaft is 82448 mm4. Determine the magnitude of the maximum bending stress in the shaft. O 19.7 MPa O 22.0 MPa O 25.4 MPa O 30.6 MPa O 28.5 MPa L₂ Pc L3

A 36-mm-diameter solid steel shaft supports loads PA = 1,400 N and Pc = 2,100 N as shown. Assume L₁ = 100 mm, L₂ = 200 mm, and L3 = 150 mm. The bearing at B can be idealized as a roller support and the bearing at D can be idealized as a pin support. The moment of inertia of the shaft is 82448 mm4. Determine the magnitude of the maximum bending stress in the shaft. O 19.7 MPa O 22.0 MPa O 25.4 MPa O 30.6 MPa O 28.5 MPa L₂ Pc L3

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.5.8P: A freight-car axle AS is loaded approximately as shown in the figure, with the forces P representing...

See similar textbooks

Similar questions

A freight-car axle AS is loaded approximately as shown in the figure, with the forces P representing the car loads (transmitted to the axle through the axle boxes) and the forces R representing the rail loads (transmitted to the axle through the wheels). The diameter of the axle is d = 82 mm, the distance between centers of the rails is Z., and the distance between the forces P and R is A = 220 mm. Calculate the maximum bending stress vmaxin the axle if P = 50 kN.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A 18-mm-diameter solid steel shaft supports loads PA = 1,400 N and Pc = 2,100 N as shown. Assume L₁ = 100 mm, L₂ = 200 mm, and L3 = 150 mm. The bearing at B can be idealized as a roller support and the bearing at D can be idealized as a pin support. The moment of inertia of the shaft is 5153 mm4. Determine the magnitude of the maximum bending stress in the shaft. B O 150.2 MPa O 317.3 MPa O 205.6 MPa O 244.5 MPa O 266.8 MPa L₂ Pc L3
A 45-mm-diameter solid steel shaft supports loads PA-1.2 KN and Pc-2.7 kN as shown. Assume that L₁ - 105 mm, L₂ = 205 mm, and 43-150 mm. The bearing at B can be idealized as a roller support, and the bearing at D can be idealized as a pin support. Determine the magnitude of (a) the maximum horizontal shear stress in the shaft. (b) the maximum tension bending stress in the shaft. L₂ C Pc Ly D
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T in kN-m that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. Answer in 2 decimal places
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 72 mm and G = 30.49 GPa. For the steel segment BC, the diameter is 48 mm and G = 83.57 GPa. Given that a = 2.09 m and b = 1.48 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 66.49 MPa in the bronze and 85.69 MPa in the steel. Round off the final answer to two decimal places.
The internal loadings at a cross section through the 120-mm-diameter drive shaft of a turbine consist of an axial force of 12.5 kN, a bending moment of 1.2 kN - m, and a torsional moment of 2.25 kN m. (Eigure 1). Figure 1.2 kN-m 12.5 kN 1 of 1 2.25 kN-m
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 70 mm and G = 33.29 GPa. For the steel segment BC, the diameter is 40 mm and G = 84.85 GPa. Given that a = 2.03 m and b = 1.38 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 64.59 MPa in the bronze and 84.39 MPa in the steel. Round off the final answer to two decimal places. d A Bronze B Steel b. Add your answer
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 66 mm and G = 34.74 GPa. For the steel segment BC, the diameter is 45 mm and 6 = 84.1 GPa. Given that a = 2.18 m and b = 1.43 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 65.48 MPa in the bronze and 81.24 MPa in the steel. Round off the final answer to two decimal places. d ... A Bronze B Steel b–
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 68 mm and G = 34.84 GPa. For the steel segment BC, the diameter is 40 mm and G = 83.59 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 69.92 MPa in the bronze and 87.06 MPa in the steel. Round off the final answer to two decimal places. d ... A Bronze B Steel b.
he compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T in kN-m that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel.
The proposed shaft is guided in rotation by two roller bearings O and C. T1 = 60 Ib T2 = 400 Ib Reactions: Ro = 293,25 Ib Rc = -178,25 Ib 1) Calculate the torsional stress of the shaft 2) Calculate the bending stress of the shaft