A 220V, 900rpm, 120A separately excited dc motor has an armature resistance of 0.05 Q. It is fed from a single phase fully -controlled converter with an a.c source voltage of 240 V , 50 Hz, Assuming continuous conduction mode of operation, Calculate (i) Find the speed of the motor when firing angle of the converter is 45 degree and motor is operating at rated torque (ii) Find the speed of the motor firing angle of the converter is 140 degree andand motor is operating at rated torque
Q: A three-phase, six-pole, squirrel-cage induction motor is to be controlled by terminal voltage…
A: Motor- A motor is a device which is used to convert electrical energy in the form of rotational…
Q: A 120-V shunt DC motor has armature resistance RA=0.2Ω and and field resistance RF=60Ω . The rated…
A: Starting current of the motor is determined as shown below
Q: A 150 V, 980 rpm, 100 A separately excited DC motor has an armature resistance of 0.2 02. It is fed…
A:
Q: The rated parameters of a separately excited DC motor are: U=420V; Ia=57,5A; Ra=0.1Ω and kgφ=0,4263…
A: given information applied voltage (V) = 420 volts, Ia=57.5 Amps, Ra=0.1Ω and kφ=0,4263 (V/rpm).…
Q: A 120-V shunt DC motor has armature resistance R,=0.2N and and field resistance Rp=602 . The rated…
A: Given DataL V = 120 V Ra = 0.2 ohm Rf = 60 ohm rated full load current = 42 A
Q: A 1200 rpm, 700V Series DC motor has an armature resistance of 20 and the field resistance of 90. If…
A: efficiency = output powerinput power = input power - lossesinput power input power to motor =…
Q: A 480-V, 100-kW, 50-Hz, four-pole, Y-connected synchronous motor has a rated power factor of 0.85…
A: As per the guidelines given to us, we can only provide the solution to the first three subparts in…
Q: Q/ A separately excited DC motor running at speed = 1100 rpm and has the following specifications:…
A: Given machine is separately and field current is constant Torque=K*armature current. Armature…
Q: C) Separately excited DC Motor of 10-HP with an armature resistance of 0.5 ohm connected directly to…
A: In separately excited dc motor , line current = supply voltage-back E.M.FTotal resistance…
Q: The speed of a 20-hp, 300-V, 1800-rpm separately excited dc motor is controlled by a three-phase…
A: Given Power P=20 HP V=300 V rated speed Nr=1800 rpm Kv =1.2 V/A rad/sec Rf =245 ohm For converter…
Q: A 220 V, 1500 rpm, 18 A separately excited DC motor has an armature resistance of 0.5 2. It is fed…
A:
Q: A 200V, 875rpm, 150A separately excited dc motor has an armature resistance of 0.06 Q. It is fed…
A:
Q: Q1. It is desired to run the motor at 1000 rpm, Find the value of the field resistance that to be…
A: 1)Given Desired speed N2=1000 rpmV=220 vRa=0.5 ΩRf=200 ΩT=constantArmature current Ia=20 Aspeed…
Q: Q5- Adjust a fire angle for a three-phase full-wave semi-controlled converter to feed the separately…
A:
Q: Consider a separately-excited DC motor with an armature resistance RA = 0.2 ohm and terminal voltage…
A: Given: Rated speed, N1=1200 rpmRA=0.2 ΩVT=130 VVF=360V
Q: Q1. It is desired to run the motor at 1000 rpm, Find the value of the field resistance that to be…
A:
Q: The shunt field of a 5-hp dc compound motor has a resistance of 200 ohms, a series field resistance…
A: According to question: Let's consider long shunt dc compound motor,…
Q: Q5- Adjust a fire angle for a three-phase full-wave semi-controlled converter to feed the separately…
A: load is separately excited DC motor load torque when motor speed is 750 rpm Vph=supply…
Q: Q19 / Draw The torque-speed characteristic of a differentially compounded DC motor.
A: If the load on the cumulative compound motor increases the torque developed also increases. But the…
Q: The speed of a 150 hp, 650V, 1750 rpm, separatley excited DC motor is controlled by 3-phase, 460v,…
A:
Q: A 220V, 900rpm, 120A separately excited dc motor has an armature resistance of 0.05 .It is fed from…
A: The solution is provided in the next step.
Q: A shunt DC motor is operated at no-load at rated voltage 220 V, speed 1700 rpm and mature current…
A:
Q: Q1. It is desired to run the motor at 1000 rpm, Find the value of the field resistance that to be…
A: In this question, We need to determine the additional resistance R in the field winding. If…
Q: a 220v, 500A,600r/min,separately excited dc motor has armarture and field resistance of 0.2 and 10…
A:
Q: A 200 hp, 1500 V cumulative compound DC motor drives a load at a speed of 800 rpm and consumes 59.68…
A: I will be attending only first 4 sub parts of the question Motor rating = 200hPInput voltage V=1500…
Q: A separately excited DC motor drives a constant torque mechanical load. The armature resistance is…
A: For a separately excited DC motor driving a constant torque load, armature resistance Ra=0.2 Ω,…
Q: A shunt DC motor has a total resistance value for all conditions as Ra=2ohm and under full load…
A: In this question we need to find a emf , line current and power supply to shunt motor
Q: A 150 V, 1400 rpm shunt DC motor is used to supply rated output power to a constant torque load. On…
A:
Q: A separately excited dc motor operating from a single phase semi-controlled converter at a speed of…
A: AC supply Voltage (Vs) = 230 V Peak value of the supply voltage (Vm) = 2 Vs = 230 2 V Back e.mf..…
Q: The rated parameters of a separately excited DC motor are: U=420V; Ia=57,5A; Ra=0.1Ω and kgf=0,4263…
A:
Q: V DC motor is listed in a catalogue as having the following specifications when operated voltage:…
A:
Q: A 2300 V, 400 HP, 50 Hz, eight-pole, 0.85 Leading PF, Y-connected synchronous motor is having a…
A:
Q: A DC, separately excited motor is used to drive a constant-torque load. The field circuit is excited…
A: DC Motor: DC Motor is an electromechanical device which converts electrical energy to mechanical…
Q: A 4 pole, 220V , DC shunt motor develops an output power of 10 kW . If Ra = 0.07 ohms , and Rsh =…
A:
Q: Q5- Adjust a fire angle for a three-phase full-wave semi-controlled converter to feed the separately…
A: Given Vph=150 Vra=0.2I0=40 AN=750 rpmkb=0.4 v/rpm
Q: Q/ A separately excited DC motor running at speed = 990 rpm and has the following specifications:…
A: A separately excited motor, excited by 240V battery. If terminal voltage V=238V and speed 990rpm…
Q: 8-) A 15-hp, 220-V series DC motor has an armature resistance of 0.120 and a series field resistance…
A: Part (a) Output power of given motor is, Po=15×746Po=11190 W Input power is,…
Q: Given a 10-hp 230-volt 1000-rpm series motor having rated load efficiency of 85.5%, Ra = 0.28 Ω, and…
A: It is given that: Pout=10 hp=7460 WN=1000 rpmη=85.5 %Ra=0.28 ΩRs=0.15 ΩVt=230 V
Q: (A shunt DC motor has a total armature resistance value for all conditions as Ra= 2 Q and under full…
A:
Q: 4. A d.c. series motor is controlled by a DC-DC drive. Drive parameters are as follows: (Ra + Rf) =…
A: Given that a dc series motor is supplied by 110V dc source through a dc-dc drive. a) Given armature…
Q: The rated parameters of a separately excited DC motor are: U=420V; Ia=57,5A; Ra=0.1Ω and kgf=0,4263…
A: Given: kgϕ=0.4263 Vrpm Constant loss = 600 W Ra=0.1Ω IAN=57.5 AV=420 V
Q: Q/ A separately excited DC motor running at speed = 1100 rpm and has the following specifications:…
A: Given data : Speed ,N=1100 rpm Terminal voltage ,Vt=238V Field voltage ,Vf=240 V Armature resistance…
Q: * A 2000, loo rpm, 1oA Separately - excited de motor is fod from a Single -phase full Converter with…
A: Given,200 V 1000 rpm 10A230 V, 50HzVm=2×230Vt=Ea+IaRaVt=Kmωm+IaRaFrom here,Km=Vt-IaRaωm…
Q: Q1. It is desired to run the motor at 1000 rpm, Find the value of the field resistance that to be…
A:
Q: A 30-hp, 250-V dc shunt motor has armature and shunt field parameters of 0.03 Ω and 125 Ω,…
A: A 30-hp, 250-V dc shunt motor armature Winding resistance Ra=0.03 ohm shunt field resistance Rsh =…
Q: Please answer the question step by step and please care to explain the question in detailed with…
A:
Q: What is the solution to this questionQ) A 250V, DC series motor has total resistance of 0.8 Ω. Its…
A: A 250 V DC series motor has a total resistance of 0.8 ohms and its full load current be 10A and…
Q: A 230 V DC shunt motor has a full-load efficiency of 89.9%. Rated (full) load is 40 hp. Motor…
A: Note: As per our company guidelines we are supposed to answer ?️only the first 3️⃣ sub-parts. Kindly…
Q: A 120-volt separately-excited DC motor has armature resistance Ra = 0.2 ohms and shunt field…
A:
Q: A 100-hp, 250- V, 400-A shunt DC motor with an armature resistance of 0.05Ω. It is desired to design…
A:
Step by step
Solved in 3 steps
- A DC chopper is used in regenerative breaking mode of a dc series motor. The dc supply is 600 V, the duty cycle is 70%. The average value of armature current is 100 A. It is continous and ripple free. What is the value of power feedback to the supply ?Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights.Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights. design the single-phase, full-wave, ac/ dc converter. show design specifications, the reason for DC motor selection. correct manual circuit, and correct automatic closed-loop control circuit
- A 48kW, 600V, 1500 rpm separately excited dc motor is controlled by single phase semi-controlled converter. The resistance of the armature is 192 and of the field is 1450. The field circuit is controlled by a single phase fully controlled converter and its firing angle is set to 20. The AC supply voltage to the armature and field converters is a single phase 220V, 60 Hz. The voltage constant is 0.946 V/A rad/s. If the armature converter firing angle is 45 and the speed is 1200 rpm; calculate the armature current and the developed torque.L-1). The 3-phase wound-rotor induction motor has .... . a) high starting torque b) low starting current c) both "a" and "b" d) neither "a" nor "b" L-2). The 3-phase wound-rotor induction.........a) motor has a wire wound rotor b) motor's rotor can be connected to an external resistive load by way of slip rings and brushes c) motor requires more maintenance than the 3-phase squirrel-cage induction motor d) all of the above L-3). The 3-phase wound-rotor induction motor's rotor circuit's resistance should be adjusted so it is__________ during starting. a) low b) high c) either "a" or "b" d) neither "a" nor "b" L-4). Will a 3-phase wound-rotor induction motor start with no external circuit connected to its rotor leads? a) yes b) no• Q5/ in a DC motor. List and describe the types of losses that occur
- Speed control of a 140 V, 1.68 kW DC motor single phase thyristor full wave AC-DC It is made by the converter. AA supply voltage 220 V (rms) Is 50. In the converter It is assumed that there is no loss. The armature resistance of the DC motor is = 0.417 Q. Very a large inductance is connected in series with the motor. The motor voltage constant is = 0.0964 V/rpm. The motor can be considered as a permanent magnet DC. According to this, a) Draw the driver (converter-motor) power circuit. b) Calculate the nominal current of the motor. c) Supply voltage, supply current, converter output voltage for ignition angle a = 30 ° and Draw the waveforms for the converter output current. d) = 950 rpm and for nominal current, d1) The firing angle of the converter, d2) Effective value of supply and thyristor current, d3) Supply power factor, calculate.Q4/B/ What are the principal characteristics of a series DC motor? What are its uses? Core Mc1. Single phase full converter is used to control the speed of separately excited DC motors. AC supply voltage is 208 V. Motor armature and field resistance are 0.5 2 and 345 2 respectively. The field current is also controlled by a full converter and the field current is set as the maximum possible value. Motor voltage constant is 0.7 V/A-rad/sec. If firing angle is 45° and armature current is 55 A, determine the angular speed of the motor. Assume armature and field current are ripple free.
- Q3 Draw the equivalent circuit of a DC Motor, Separated Excited DC Motor and Compounded DC Motor. Label each component properly (a)1) P.f of inductive load is corrected by connecting . . across it. .... ...... 2) Open circuit test measures . losses. 3) The output variables of a motor are and ........ ... .... 4) For a motor output power is given by ...... 5) Flux control, voltage control, and armature control are three methods for ....... of dc motor. 6) A transformer takes 100V at primary and gives 50V at secondary, its turn ratio equals 7) The given set of equations represents . . Ea – laRa = Vr , la = IL , %3D Rf 8) The given set of equations represents. la = !, + IL, VT Rf Ea – laRa = Vr , 9) The given set of equations represents . Ea – laRa – IseRse = Vr, la = Ise = l, %3D | 10). .. has more initial torque than shunt dc motor.A freewheeling DC motor is driven with 1000 rpm and a nominal load torque of 80Nm. The field circuit resistance is 200 and the armature circuit resistance is 0.2 O. The field coils are fed with a zero degree transmission angle through a single-phase fully controlled converter connected to a single-phase 240V source. The armature circuit is fed from a single phase 400V source through another fully controlled converter. Magnetic saturation has been neglected, the motor constant is given as 0.8 V - s / A - rad. Assuming that there is no fluctuation in armature and field current, find the control angle of the converter feeding the armature at nominal load. If you want to leave the question blank, click again on the option you marked.