A (160+Reg. No.) kN force is applied as shown at the end of a hot-rolled steel beam. Neglecting the effect of fillets and of stress concentrations, perform calculations in MS excel or MATLAB for the principal stresses in the beam to satisfy a design specification that they be equal to or less than 150 MPa. If the principal stresses are more than the given value, what would you change in the beam so that satisfy the required stresses. 210 mm 13 mm b 103.5m 110 mm 160kN +Reg No. 0.4m (b) (a) Figure: Hot-rolled cantilever steel beam a) 3D view of the beam b) Cross-section of the beam

A (160+Reg. No.) kN force is applied as shown at the end of a hot-rolled steel beam. Neglecting the effect of fillets and of stress concentrations, perform calculations in MS excel or MATLAB for the principal stresses in the beam to satisfy a design specification that they be equal to or less than 150 MPa. If the principal stresses are more than the given value, what would you change in the beam so that satisfy the required stresses. 210 mm 13 mm b 103.5m 110 mm 160kN +Reg No. 0.4m (b) (a) Figure: Hot-rolled cantilever steel beam a) 3D view of the beam b) Cross-section of the beam

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Angle 1 Tyx Tyx Figure 1 Point A- x-direction stress 60MPA(compression), y-direction stress 40MPA(tension), negative shear stress 30MPA Using your assigned point determine the following for the yz-plane: a) From basic priciples determine the stresses on the plane of the indicated angle 1-30°, Show al calculations. Draw the orientation of the stress block for this scenario. b) Repeat question (a) using a Mohr circle. c) Using a Mohr circle, determine and draw the maximum stress block of the in-plane maximum shear and principle stresses. d) Determine the stresses and orientation of the stress block where the normal stress is zero. Make use of the stress transformation equations. e) Determine the values of absolute maximum shear stress and corresponding normal stress.
Find stress of a aluminum cylinder of diameter 12.8mm and gauge length 50.8mm. The force applied is 47,500N.
Two forces are applied on the beam shown below. (a) Determine the normal and shear stresses at point B on the shown cross-section. (b) Show the state of stress at the point B on a volume element. 400 lb B 1 in. 2 in. 500 Ib 2 in 10 in. 1.5 in. 1.5 in. Show your steps and highlight the following answers please I =
Answer p1 and Part 2: Determine the shear force acting at each of the following locations:(a) x = 11.0- ft (i.e., just to the left of point B)(b) x = 11.0+ ft (i.e., just to the right of point B)(c) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2.Answers: a) V = ____ kips b) V = ____ kips c) V = ____ kips Part 3: Determine the bending moment acting at each of the following locations:(a) x = 11.0 ft (i.e., at point B)(b) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the bending-moment sign convention detailed in Section 7.2. Answers: a) M = ____ kips-ft b) M = ____ kips-ft Part 4: Use your shear-force and bending-moment diagrams to determine the maximum bending moment, Mmax, and its location, xmax. Use the bending-moment sign convention detailed in Section 7.2.Answers: Mmax = ____ kips-ft xmax = ____ ft
2. The stress at a point of a machine component are 200MPa tensile and 100MPa compressive. Using Mohr’s Circle method find the intensities of normal, shear and resultant stresses on a plane inclined at an angle of 300 with the tensile stress. Also find the magnitude of shear stress in the component.
1. A shaft 80 mm diameter transmits power at maximum shear stress of 63 MPa. Find the length of a 20 mm wide key required to mount a pulley on the shaft so that the stress in the key does not exceed 42 MPa. [Ans. 152 mm] 2. A shaft 30 mm diameter is transmitting power at a maximum shear stress of 80 MPa. If a pulley is connected to the shaft by means of a key, find the dimensions of the key so that the stress in the key is not to exceed 50 MPa and length of the key is 4 times the width. [Ans. / 126 mm] 3. A steel shaft has a diameter of 25 mm. The shaft rotates at a speed of 600 r.p.m. and transmits 30 kW through a gear. The tensile and yield strength of the material of shaft are 650 MPa and 353 MPa respectively. Taking a factor of safety 3, select a suitable key for the gear. Assume that the key and shaft are made of the same material. [Ans./= 102 mm]
A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding. 24m
Calcuate Bending From Point A to Point B and Point A to Point C, Calcuate torsion From Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in
A 6-inch diameter pulley mounted on a 2-inch shaft as shown transmits 9 kW at 1000 rpm. What is the combined stress acting on the shaft?
Consider the 2-D state of stress shown below. Using the provided scales graph the Mohr's Circle for the 2-D state of stress with “full" details II-Obtain the Principal Stresses, the Maximum Shear Stress, and complete the table below III- Draw the Planes of Principal and Maximum Shear Stresses in the space provided below Provide "full" details and Use 3 Sig. Fig. in this problem Oy = 15 Ksi Tcw > S y Ox =10 Ksi Тух 5 Ksi 10 5 -20 -15 -10 5 10 15 20 5 10 Tccw > S' O Avg. TMax. 01 02 Op1
A circular rod is stretched by a force of 3kN. Solve the diameter of the rod if the stress is not to exceed 153MPa.
A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 m is under tension. If the wire length extension is 2.5 mm, calculate the stress in the wire. Give your answer in N/m2to 2 decimal places. (show all work)