Please answer and show work, will give thumbs up! ZminA 12 V zener diode has r.=52, minimum current I -5 mA, a current of 20 mA at 12 V.The maximum power dissipation P = 600 mW at room temperature. The supply voltage is20V±2V The load draws a constant current I₁= 15 mA Find the following:ZmaxVs= 20 V±10%1| R$a) V.20b) Maximum current Izmax'Examine the circuit and answer the followingc) Output voltage Vo at Izmin'd) Resuch that minimum current flows through zener diode,Anser the following assuming R, is disconnectede) Current I, when Vs=22V,f)AV due to AVs=±2V,g) Line regulation|FM|-oVo15 mAR₁

Note: We are authorized to answer the first three sub-parts at a time, so we are answering the first…

A 12 V zener diode has r.=52, minimum current Izmin=5 mA, a current of 20 mA at 12 V. The maximum power dissipation P = 600 mW at room temperature. The supply voltage is 20V±2V. The load draws a constant current I₁= 15 mA. Find the following: Zmax Vs= 20 V±10% a) V zo b) Maximum current Izmax' Examine the circuit and answer the following c) Output voltage Vo at Izmin' RS

A 12 V zener diode has r.=52, minimum current Izmin=5 mA, a current of 20 mA at 12 V. The maximum power dissipation P = 600 mW at room temperature. The supply voltage is 20V±2V. The load draws a constant current I₁= 15 mA. Find the following: Zmax Vs= 20 V±10% a) V zo b) Maximum current Izmax' Examine the circuit and answer the following c) Output voltage Vo at Izmin' RS

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

In the circuit shown below, the ideality factorn of the diode is unity and the voltage drop across it is 0.7 V. The dynamic resistance of the diode at room temperature is approximately 1.7 V 31 k2
uO 9:.0 A docs.google.com * ZAIN IQ l. Q3/B: Assume an ideal diode model for all the diodes in the circuit below. calculate voltages and currents through D1 and D2 9kQ 1N1199C R2 D1 18KQ 1N1199C D3 1N1199C V2 =12 V R3 1kQ R4 5kQ 1.22 V 11 mA 0.5 A O VD1 ID1 VD2 ID2 صفحة 4 من 6
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
How do you identify the anode of an unmarked diode? When the forward current of a diode increases, its forward resistance The current flowing in a reverse-biased diode circuit is extremely while the resistance of the diode is extremely The Vz of a zener diode will fairly constant even if the power supply voltage The series resistor Rs is used with the zener diode to the zener current Iz to a level.
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1
3: Using silicon diode design a clamper that will produce output V,-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
Given the following circuit with VDD= 9.2 V, R=2.3 k2, then the current Iis: Use the CVD model for the diode, with VD = 0.65 V. I VDD a. 0.004000 A O b. 3.717391 A OC. 0 A d. 4.000000 A e. 0.003717 A R + VD -
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
1. Determine Vpout for the circuit in below and draw Vauts assume the diode is the silicon type. 10 k +10 V-- V. ov R, 100 k IN914 -10 V- 2. What is the output voltage that you would expect to observe across R, circuit of Figure below? Assume that RC is large enough to prevent significant capacitor discharge. +24 V 10 uF RL 10 kn V. ov. IN914 -24 V
Questions 1 V, is a 60Hz source with a peak voltage VP-120V is feeding a rectifier, assume ideal diode. The load resistance has a value of R= 10 kn. If ripple voltage Vr = 2V, the Diode average current Ipavg is VI Select one: None b. 580mA 850mA O c. Od 245mA O e. 425mA D C C: R www Q+ Vo
There are two LEDS that can be used as a polarity detector. Apply a positive source voltage and a green light results. Negative supplies result in a red light. Packages of such combinations are commercially available.Find the resistor R to ensure a current of 20 mA through the "on" diode for the configuration. Both diodes have a reverse breakdown voltage of 3 V and an average turn-on voltage of 2 V. * +8 V Red Green 350 ohms 330 ohms 310 ohms 300 ohms None of the above