Solve using Fbd and equation.Have 30min only 9-3. Determine the tensile stress in each segment of the barshown. Segment AB has a square cross section 2 in. by 2 in.Segment BC has a circular cross section with a diameter of 1.75in. The tensile load P = 75 kips.P|Problem 9-32₁2'-0"B1.75"3'-6"сP

Answered: Image /qna-images/answer/7fc2895b-f4dd-4725-93ec-6e053119300e.jpg

Answered: 9-3. Determine the tensile stress in ea…

9-3. Determine the tensile stress in ea shown. Segment AB has a square cros Segment BC has a circular cross section in. The tensile load P = 75 kips. P Problem 9-3 2⁰ 2'-0" B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

250 mm A D P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars (E=205GPA, G,A=82GPA) and is pinned to plate ABC using a 5 mm diameter pins as shown in the figure. The yield strength of the pins is T,=890MPA. Plate ABC is a right triangle and is fixed along its edge BC. A 25KN Force P is then applied at end D causing a lateral strain in member AD with magnitude equal to 7.5x104mm/mm. This also causes Point A to displace only along the horizontal resulting to a shear strain at point A equal to y,=+0.00165rad. Determine the following: 1. Poisson's ratio of material used in member AD, vD 2. The normal strain in member AD, CAD 3. The average stress experienced by pin A, TA 4. Factor of Safety of pin A with respect to yielding, FS,A 5. Displacement of point D, A,
250 mm A D P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars (E0=205GP,, Ga=82GPA) and is pinned to plate ABC using a 5 mm diameter pins as shown in the figure. The yield strength of the pins is T,=890MPA. Plate ABC is a right triangle and is fixed along its edge BC. A 25KN Force P is then applied at end D causing a lateral strain in member AD with magnitude equal to 7.5x10-mm/mm. This also causes Point A to displace only along the horizontal resulting to a shear strain at point A equal to y,=+0.00165rad. Determine the following: 1. Poisson's ratio of material used in member AD, vAD 2. The normal strain in member AD, caD 3. The average stress experienced by pin A, T, 4. Factor of Safety of pin A with respect to yielding, FS,A 5. Displacement of point D, A,
Problem 1: The rigid bar ABC is supported by AD and BE. Determine: a. Inclination of member ABC after loading b. 8 at point E Members Properties: Member Materials Modulus Cross- sectional Area of Elasticity AD Aluminum 70GPA 450mm2 ВЕ Steel 200GPA 550mm2 E O •Im O:3m 45kN. t 0 4m
Determine the maximum tensile and compressive bending stresses developed in the beam shown. The cross-section has the given properties. NA 1-35 x 10mm a. RA = b. RE= c. fb(c) = d. fb(T) = 80 mm 200 mm A 1.5m kN KN 5kN m MPa MPa B 1.5m SkN/m 2m 5KN n 2m 4
1. The assembly is shown is attached to supports at A and D. Section BCD is a solid 2" diameter aluminum [E = 10,000 ksi] rod. Steel [E = 30,000 ksi] tube AB has an outer diameter of 3.50" and a wall thickness of 0.216 in. Determine (a) the stresses is sections AB, BC and CD, and (b) the deflections of joints B and C. [OAB = 3.40 ksi (C), Osc = 5.863 ksi (T) Oc, = 4.959 ksi (C), 8, = 0,0054"– , d. = 0,02975"→] %3D %3D %3D %3D 13 kips 17 kips A C 13 kips 17 kips 4 ft 5 ft 5 ft
A structural member is fabricated with the cross section show below and is eccentrically loaded with F. - 26--| F 2t F b. Use G = 77.2 GPa. If I = 4 m, t= 3 mm, b = 80 mm, and F = 121 kN, Determine the maximum shear stress due to torsion. Select the correct response: 168.056 MPa 215.278 MPa 155.556 MPa of 133.333 MPa 22
1-45. The truss is made from three pin-connected members having the cross-sectional areas shown in the figure. Determine the average normal stress developed in each member when the truss is subjected to the load shown. State whether the stress is tensile or compressive. -0.6 in. AAC -3 ft- Auc= 0.8 in.2 AAB 1.5 in. 500 lb B
Strain in rods is zero prior to applying load Determine load P such that the axial stress in the steel pipe is 200 MPa P Imm GAP RIGIO PLATE .6m B RIGID SUPPORT 30 mm x 30 mm. AL BAR E = 73 GPA 100 mm E = 200 G PO A B A ØSTEEL PIPE w/ 5mm WALL
*4-88. If the allowable normal stress for the bar is O allow = 120 MPa, determine the maximum axial force P that can be applied to the bar. %3D 5 mm 40 mm 20 mm P- r = 10 mm 20 mm
Q3. Two steel plates (A572, Fb = 50ksi) are welded together to form an inverted T-beam. Determine the maximum bending stress developed. ( %3D | 10 Marks) 10k 15 k 6ft 5 ft 10 ft 5 ft A B 8ft 1ft
Two steel plates are welded together to form an inverted T-beam and are loaded as shown below. Determine the maximum bending stress developed. Also, determine the maximum shear stress at the neutral axis of the cross section. The following Inte Av = 9K Bv = 11K location of centroid = 3.56" above X-Ref Shear diagram Moment diagram 1" x 10" steel plate 1" x 8" steel plate X-reference A 6' 8K 12' 24' 12K 6' B of your work is accurate. Yo ment Mmax = 66K' Vmax 11K Moment of Inertia = 218 inª
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm