6m T 10m A 8m Figure 4 A B 6. A horizontal beam AB of mass m = 20kg is supported from end B by a cable and hinged to a A vertical wall at end A. Calculate the magnitude of the tension T in the cable when Batman, who has a mass M = 80 kg, stands midway along the beam. What are the x and y components of the force at the hinge?

6m T 10m A 8m Figure 4 A B 6. A horizontal beam AB of mass m = 20kg is supported from end B by a cable and hinged to a A vertical wall at end A. Calculate the magnitude of the tension T in the cable when Batman, who has a mass M = 80 kg, stands midway along the beam. What are the x and y components of the force at the hinge?

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 12.6OQ: A 20.0-kg horizontal plank 4.00 in long rests on two supports, one at the left end and a second 1.00...

See similar textbooks

Similar questions

A 20.0-kg horizontal plank 4.00 in long rests on two supports, one at the left end and a second 1.00 m from the right end. What is the magnitude of the force exerted on the plank by the support near the right end? (a) 32.0 N (b) 45.2 N (c) 112 N (d) 131 N (e) 98.2 N
Consider the 120-cm board supporting three loads as shown below. The beam weighs 45 grams. If the system is in equilibrium, a. what is the magnitude of the force exerted by the pin support to the board? b. Find the perpendicular distance, x, of the pin support from the left end of the board. 30cm A В C 259 30g 75g
A uniform drawbridge must be held at a 38o angle above the horizontal to allow ships to pass underneath. The drawbridge weights 55000 N and is 15.0 m long. A cable is connected 3.5 m from the hinge where the bridge pivots (measured along the bridge) and pulls horizontally on the bridge to hold it in place. What is the tension in the cable? Find the magnitude and direction of the force the hinge exerts on the bridge. If the cable suddenly breaks, what is the magnitude of the angular acceleration of the drawbridge just after the cable breaks? What is the angular speed of the drawbridge as it becomes horizontal? What is the velocity of the drawbridge, just before it “hits” (i.e. goes horizontal)?
A beam with a length of 2 m and a mass of 10 kg supports a 50 kg box. The beam is connected to a wall by a hinge at its base and a horizontal wire. The wire is connected to the beam 1.5 m from the hinge and makes an angle θ of 35o to the beam. The goal is to find the tension in the wire and the horizontal and vertical components of the force exerted by the hinge on the board
A uniform horizontal beam with a length of 8 m and a weight of 200 N is attached to a wall by a pin connection. Its far end is supported by a cable that makes an angle of 53° with the beam. If a 600-N person stands 2 m from the wall. What is the ?tension in the cable 53.0% 8.00 m .A None .B N 410
A beam with length of 2 m and a mass of 10 kg supports a 50 kg box. The beam is connected to a wall by a hinge at its base and a horizontal wire. The wire is connected to the beam 1.5 m from the hinge and makes an angle θ of 35o to the beam. The goal is to find the tension in the wire and the horizontal and vertical components of the force exerted by the hinge on the board. Suppose the maximum tension that the wire can withstand is 1500 N. What is the maximum load that the hinge can support before the wire breaks?
A uniform rod has one end attached to a vertical wall by africtionless hinge. A horizontal wire runs from the other end of the rodto a point on the wall above the hinge and holds the rod at an angle θabove the horizontal. You vary the angle u by changing the length ofthe wire, and for each θ you measure the tension T in the wire. You plotyour data in the form of a T-versus-cot u graph. The data lie close to astraight line that has slope 30.0 N. What is the mass of the rod?
A beam with length of 2 m and a mass of 10 kg supports a 50 kg box. The beam is connected to a wall by a hinge at its base and a horizontal wire. The wire is connected to the beam 1.5 m from the hinge and makes an angle θ of 35o to the beam. The goal is to find the tension in the wire and the horizontal and vertical components of the force exerted by the hinge on the board. A. In order to find the tension in the string, which point should we select to write ?(a)Top left end of the beam(b)Point where wire is connected to the beam.(c)Middle of the beam (where mg acts).Bottom right end of the beam(d) Use the point you identified in C to calculate the tension in the string.
mb Ed- ms A horizontal L=1.5 m long mb3D14 kg uniform bar is hinged on the left end and pulled at the right end by a cable. The cable makes 31° angle with horizontal. A 15 kg store sign is suspended below the bar at d=0.20 m from the right end. Find the magnitude of vertical hinge force.
One end of a uniform rod of weight w = 73.5 N and length L = 2.55 m is supported by a cable at an angle of ? = 37.0°above the rod. The other end rests on a small frictionless support and presses into a wall as shown in the figure. Determine the magnitude n of the vertical normal force exerted by the support on the rod and find the magnitude T of the tension in the cable.
Q10 In the figure, one end of a uniform beam of weight 310 N is hinged to a wall; the other end is supported by a wire that makes angles θ = 27° with both wall and beam. Find (a) the tension in the wire and the (b) horizontal and (c) vertical components of the force of the hinge on the beam.
A 6.0 m plank with a mass of 50 kg is supported on both ends. An 80 kg worker stands on the plank 1.5 m away from the left end. What weight must each end of the plank support? Separate your answers by a comma (i.e. 340 N, 567 N - the first answer for the left end, the second answer for the right end). Express your answer as a whole number (no decimal). Add the appropriate units.