6) The connection shown in the figure uses 20mm diameter A325 bolts. The tension member is A36 steel (Fy= 248 MPa, Fu = 400 MPa) and the gusset plate is A572 steel (Fy=290 MPa, Fu = 415 MPa). Determine the design strength of the connection (in kN) considering block shear rupture. 37.5 mm 75 mm 37.5 mm 9 mm gusset P 12 mm x 150 mm 37.5 mm 75 mm 37.5 mm

6) The connection shown in the figure uses 20mm diameter A325 bolts. The tension member is A36 steel (Fy= 248 MPa, Fu = 400 MPa) and the gusset plate is A572 steel (Fy=290 MPa, Fu = 415 MPa). Determine the design strength of the connection (in kN) considering block shear rupture. 37.5 mm 75 mm 37.5 mm 9 mm gusset P 12 mm x 150 mm 37.5 mm 75 mm 37.5 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.5.3P

See similar textbooks

Similar questions

Problem. A bolted connection shown consists of two plates 300 mm x 12 mm connected by 4 - 22 mm diameter bolts. 12 mm bolts t=12 mm t=12 mm P. P- P 300 75 75 75 Edge distances -75 mm dhole for tensile and rupture d, +3 mm dnole for bearing strength for L- de +1.5 mm Fy 248 MPa F.- 400 MPa
The connection shown is subjected to a tensile force of P = 100 kN. The allowable shear stress for the bolts is 100 MPa. Assume each bolt supports an equal portion of the load. Determine the required diameter of the bolts. a. 20.6 mm b. 25.2 mm c.35.7 mm d.17.8 mm choose letter of correct answer
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
Bolted and Riveted Connections From the bolted connection shown, the diameter of bolts is 18mm0 with the hole diameter equal to 3mm bigger than the bolt, the angular section is 100 x 75 x 8 mm, with an area of 1340 mm2. Thickness of the gusset plate is 9mm. The gusset plate and angle arc A36 steel with Fy = 250 MPa and Fu = 400 MPa. Determine the tensile capacity of the connection based on gross area. Determine the tensile capacity of the connection based on effective net area using a reduction factor of 0.85. Determine the tensile capacity of the connection based on gross area.
A bolted connection shown consists of two plates 300mm x12mm connected by 4 - 22 mm diameter bolts. Edge distances = 75mm dhole for tensile and rupture = db + 3 mm dhole for bearing strength for Lc = db + 1.5 mm Fy = 248 Mpa Fu = 400 Mpa Fn = 330 Mpa Use LRFD design method. Determine the design strength due to the gross yielding of plates. (kN)
4. Determine the design strength of the connection shown in the Figure below. Thebolts are 25 mm diameter A490 bolts with the threads not in the plane of shear.A36 steel is used (Fy = 250 MPa, Fu = 400 MPa).a. Compute the shear strength for all bolts.b. Compute the bearing strength for the tension member on all bolts.c. Compute the bearing strength for the gusset plate on all bolts.d. Compute the tensile strength of the tension member.e. Compute the design strength of the connection.
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
Design a welded connection for an MC9x23.9 of A572 Grade 50 steel connected to a 3/8-inch-thick gusset plate (Figure 6). The gusset plate is A36 steel. Show your results on a sketch, complete with dimensions. = 3/8" Figure 6 D = 48 k L = 120 k MC9 x 23.9 a. Use LRFD. b. Use ASD.
2. The figure shown is bolted with a diameter of 22mm. The inner plate material is 12mm x 315mm and the outer plate material is 9mm x 315mm. Assume hole diameter is 2mm larger than the bolt. T/2 T/2 F, = 345MPA, F, = 450MPA, F, = 207MPA, F, 1.2F, for bearing type connection. F, a friction type connection. = 117MPA for 45mm 75mm T/2 a. Determine the tensile capacity of the plates if it is a bearing type connection. b. Determine the tensile capacity of the plates if it is a friction type connection. c. Compute the minimum theoretical length of the lap if it is a bearing type connection. 75mm T/2 75mm 45mm A в А
1. what is the bolt shear capacity of the shear connection in kips? (2 decimal places)A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
A bolted connection shown consists of an angular section L 150mmx100mm x8mm. Bolt diameter = 18mm. Determine the effective net area of the section. (Ae). Properties of an L150x100x8: Area = 1,894 mm2 Fy = 248 MPa Fu = 400 MPa x = 23 mm y = 48 mm 50 50 50 50 50 50 150 40 www.AwNNO 60 100 50 P
Calculate and check the design strength of the connection shown below. Is the connection adequate for carrying the factored load of 65 kips. -3/8 in. А36 5 x % 125 АЗ6 2.50 65 k 1.25 % in, bolts 1.25 2.50 1.25