5. A standard subtense bar, a stadia rod and a transit were set up at points B, R and T, respective The bearing of line TB is N 36°42' W, and S 82°37' W for line TR. The subtended angle on the subtense bar is 01°45' while the upper and middle stadia hair readings on the stadia rod are 3.82 3.44, respectively. Determine the distance between: a. Transit and subtense bar (TB) b. Transit and stadia rod (TR) c. Subtense bar and stadia rod (BR)

5. A standard subtense bar, a stadia rod and a transit were set up at points B, R and T, respective The bearing of line TB is N 36°42' W, and S 82°37' W for line TR. The subtended angle on the subtense bar is 01°45' while the upper and middle stadia hair readings on the stadia rod are 3.82 3.44, respectively. Determine the distance between: a. Transit and subtense bar (TB) b. Transit and stadia rod (TR) c. Subtense bar and stadia rod (BR)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

а) Calculate the support values b) Draw the cross section effect value diagrams 3kN/m 10KN 6kNm B 1m 0.75m
DETERMINE THF SLOPE AF A AND DEFLECTON AT B USING MOM ENT- AKEA METHOD GOK 40 K t 20pt
0O REDMI NOTE 9 PRO O AI QUAD CAMERA H.W. A cable is attached to the 20-kg plate B, passes over a fixed peg at C, and is attached to the block at A. Using the coefficients of static friction shown, determine the smallest mass of block A so A. that it will prevent sliding motion of B down the plane. HA=0.2 HB=0.3 30°
The force-couple system shown acts on a trapezoidal plate. a. Determine the value of M, if the system shown is equivalent to a single force acting at point C. b. The system shown is equivalent to a force-couple system consisting of R and M2 = 3000 kip-in clockwise. If M, in this case is 120 kip-in counterclockwise, determine the point of action of the resultant force R along line CD. 50 1YZ kips 10 in 1X in 10 in B 20 kips 35 kips 8X kips 2Y in M1 50 1YZ kips Parameters X = 7, Y = 8, Z = 4 1X in 17 in 2Y in 28 in 8X kips 1YZ kips 87 kips 184 kips 18 in
Fobe Acrobat Reader DC indow Help exercisechapter3.pdf x 2 /2 135% 4. Determine the vertical displacement of joint Cof the truss. Each member has a cross-sectional area of Use the method of virtual work. Given E = 200 GPa. A 300 %3D mm2. H. 3 m E- B 4 m -4 m 4 m - 4 m 3 kN 3 kN 4 kN (Answer: 4.91 mm
SAQ 3 Determine the force-couple system acting at point 0. y 50 N 90 N C 40° B 40 N m 400 mm 1300 mm A 4 800 mm A 100 N 3 Answers: R = 83.4 N, 35° S of E, C = 87.4 N m, CW Ww 009 500 mm-
just answer the first line (AB). just show me the solution how, in both bearing and both azimuth. thank you.
44. Given an angle A such that (SecA + 2) (2SecA – 1) = 0. Determine where A terminates. A. I and IV B. I C. II and III D. I and II
The horizontal bar is supported by two cables AC, AB, and the ball-and-socket joint at O. Calculate the tension in cable AB given that F = 3867 N. y 3 m 3 m B 5 m 5 m 6 m 2 m F A. TAB = 4313.6 N %3D B. TAB = 3466.4 N %3D C. TAB = 2900.2 N %3D D. TAB = 4833.8 N %3D E. TAB = 5800.5 N %3D 21
60N LO 30 Nm, CCW 30 Nm, CW Q 270 Nm, CCW 270 Nm, CW LP L C. 1. Which of the following gives the moment of the 90.0 N-force about the center of the circular plate, 0? 44 510 N-M 2. Which of the following force and couple set acting at point O is equivalent to the given forces applied to the circular plate? 3. Which of the following single forces is equivalent to the given forces applied to the circular plate? A. B. B. 570 N-M 224 N 40° 231N 3m 150N 33.8⁰ 27.4° A P 90N LO D. А 44 1150 N-M 1150 N-M SON P 224 N 231N 33.8⁰ 27.4° P P A. LO 27.4⁰ 231 N C. 3m 33.80 231 N O O 2.28 m L D. L 56.20 224 N 33.8° 224 N A O 2.28 m 2.28 m
9 of 20 - / 5 三 View Policies Current Attempt in Progress In the figure, suppose the length L of the uniform bar is 3.0 m and its weight is 190 N. Also, let the block's weight W = 280N and the angle 0 = 31°. The wire can withstand a maximum tension of 450 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A? com II -NM
Draw the B.M.D for the following , (EI) is constsnt 50kN B 3m 30° A