5 in M 20 in 30° Q3.) The weight of the disk and the bar are 50 lb and 20 lb respectively. The static and kinetic friction coefficients between the disk and the surface is µ = 0.6 and k = 0.45 respectively. Find: a) the largest counter-clockwise moment M that can be applied on the disk without rotation, b) the counter-clockwise moment M required to make the disk rotate at constant speed.

5 in M 20 in 30° Q3.) The weight of the disk and the bar are 50 lb and 20 lb respectively. The static and kinetic friction coefficients between the disk and the surface is µ = 0.6 and k = 0.45 respectively. Find: a) the largest counter-clockwise moment M that can be applied on the disk without rotation, b) the counter-clockwise moment M required to make the disk rotate at constant speed.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. The structure shown in the figure has a motor on the top of the column. When the motor rotates, try to find the maximum horizontal displacement and the amplitude of the column end bending moment. It is known that the weight of the motor and the structure is concentrated on the top of the column, W=20KN, the amplitude of the horizontal centrifugal force of the motor FP-250N, the motor speed n=550r/min, the linear stiffness of the column i=EI,/h=5.88*10$N•cm Fp(t)=Fpcos Ot I→∞ EI El h=6 m
The bar rotates in the horizontal plane about a smooth pin at the origin. The 2-kg sleeve A slides on the smooth bar, and the mass of the bar is negligible in comparison to the mass of the sleeve. The spring constant is k = 400 kN/m and the spring is unstretched when r = 0. At t = 0, the radial position of the sleeve is r = 0.2 m, and the angular velocity of the bar is 16 rad/s. What is the angular velocity of the bar when r is increased by 0.05 m? @o A k
In the truss shown, A =1000 mm², E = 200 GPa and the coefficient of thermal expansion is 12 x10 6/°C. Determine the vertical displacement at B due the forceapplied to the truss 100 KN 100kN + 4 m B C 3m 3m Zoom image A
Set-up the overall stiffness matrix necessary to compute the nodal displacements at B and C. Compute the member forces of AB and BC and then determine the reactions at A and C. El=constant. 30 KN/m A 6m B 4 m
Q2. Determine the density of the rectangular component (i.e. a) in kg/m and the location of the equivalent point load measured from point A so that it causes an upward 50 N force and a 300 Nm couple moment reactions at A. A a kg/m 0.5 m
A hole is punched at A in a plastic sheet by applying a 540-N force P to end D of lever CD, which is rigidly attached to the solid cylindrical shaft BC. Design specifications require that the displacement of D should not exceed 15 mm from the time the punch first touches the plastic sheet to the time it actually penetrates it. Determine the required diameter of shaft BC if the shaft is made of a steel with G = 77.2 GPa and Tall = 80 MPa. D 500 mm 300 mm The required diameter of shaft BC is mm.
Rigid bar ABC is supported with a pin at A and an elastic steel rod at C. The elastic rod has a diameter of 25 mm and modulus of elasticity E 5 200 GPa. The bar is subjected to a uniform load q on span AC and a point load at B. Calculate the change in length of the elastic rod. What is the vertical displacement at point B? Rigid bar A Elastic rod q = 5 kN/m 2.5 m 0.75 m c↓ C -0.75 m- |P = 10 KN B
%3D If the intensity of the distributed load acting on the beam is w = 3KN/m, determine the reactions at the roller A and pin B. 3 TA
Given: Figure TOS 2103: W = 5044 N, (a) Find the value of X so the deflection at the free ends is zero. (b) Solve for the Reactions at the supports [kN] (c) Solve for the maximum value of Eid, [kN- mm³] (d) Solve for 0_A in degrees. W 5 m. Figure TOS 2103
Ql:- The coplanar force system shown in Figure below is subjected to a couple moment (M) and three forces. Two forces are known in magnitude and direction and shown in the Figure (150 N and 60 N). The third force is passing through the center of the semi-circle (point C). The resultant of all these forces is a single couple (750 N.m) counterclockwise. a) Determine the magnitude and direction of the third force. b) Determine the magnitude of moment (M). c) Replace the couple (M) by two vertical equal forces acting at D and E. d) Replace the force (150 N) by and single force at D and a couple. Radius 5 m 150 N 60 N
Use the virtual work method to find the horizontal movement at E, knowing that member AB is 5mm too short and members AF, FG, GH, HE have an increase in temperature of 15°C. Knowing that the coefficient of thermal expansion for the truss material is 1.2x105/°C. The truss system has pin support at A and roller support at E. 75 kN 100 kN (3000 mm2) * (3000 mm2) (2000 mm?) 9 m (3000 mm2) mm²) (2000 mm2) mm2) (3000 mm2) (2000 (2000 E (3000 mm2)B(3000 mm2) C(3000 mm²)D(3000 mm?) 4 at 6 m = 24 m E = 200 GPa (3000 mm2)
Determine the force P required to force the 16° wedge under the 97-kg uniform crate which rests against the small stop at A. The coefficient of friction for all surfaces is 0.37. 16° Answer: P = i 1.8 m 97 kg 0.7 m A 16° N