5-For single phase half-wave controlled rectifier with a freewheeling diode connected across the inductive load, the supply voltage is 220V (RMS). The mean value of the output voltage for a=45 is: 100.7V 70.9V 84.5V 6-For fully controlled single phase bridge rectifier with inductive load (R=102, L=50mH), F=50HZ and a=45', the load current is: Continuous discontinuous verge continuous 7-Fully controlled three phase bridge rectifier circuit is supplied through delta-star transformer. For highly inductive load, the waveform of the line supply current (primary line current of the transformer) is:

5-For single phase half-wave controlled rectifier with a freewheeling diode connected across the inductive load, the supply voltage is 220V (RMS). The mean value of the output voltage for a=45 is: 100.7V 70.9V 84.5V 6-For fully controlled single phase bridge rectifier with inductive load (R=102, L=50mH), F=50HZ and a=45', the load current is: Continuous discontinuous verge continuous 7-Fully controlled three phase bridge rectifier circuit is supplied through delta-star transformer. For highly inductive load, the waveform of the line supply current (primary line current of the transformer) is:

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V rmsh soHz} VL-DC =20V 0.01 F 0.02 F 0.0167 F None of the above
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
29. Does an increase in reverse bias for a Varactor diode cause an increase or decrease in capacitance? 30. If the load current through a SCR (Thyristor) reduces to almost zero, what will be the result?
A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 250 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
In a single phase full wave controlled rectifier connected to Inductive load (with freewheeling diode) find the expression for the average value of voltage across the load when supply voltage is Vs = Vm sinwt and firing angle = a. Vm/TT cosa 2Vm/TT cosa Vm/TT (1+cosa) 2Vm/TT (1+cosa)
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
In a full wave rectifier circuit involving double diodes, a sinusoidal input signal of the following nature is applied e=10 sin(500*pi*t) V. What will be value of the dc voltage obtained at the output of the rectifier.
Determine the value of RL that will establish maximum power conditions for the Zener diode.