4)Mark the correct statements: a) The frequency at the output of a half-wave rectifier circuit is 30 Hz b) The frequency at the output of a full-wave rectifier circuit is 60 Hz. c) To calculate the average voltage (DC) at the output of a full wave rectifier we use the formula: Ucc = 0.636 * Up. d) When using a bridged full wave rectifier, we know that the loss at the depletion barrier will be 2 * 0.7 Volts. e) None of the statements is correct.

4)Mark the correct statements: a) The frequency at the output of a half-wave rectifier circuit is 30 Hz b) The frequency at the output of a full-wave rectifier circuit is 60 Hz. c) To calculate the average voltage (DC) at the output of a full wave rectifier we use the formula: Ucc = 0.636 * Up. d) When using a bridged full wave rectifier, we know that the loss at the depletion barrier will be 2 * 0.7 Volts. e) None of the statements is correct.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
Assume the input signal to a rectifier circuit has a peak value of VM = 12 V and is at a frequency of 60 Hz. Assume the output load resistance is R = 2 k and the ripple voltage is to be limited to Vr = 0.4 V. Determine the capacitance required to yield this specification for a (a) full-wave rectifier and (b) half-wave rectifier.
The rectifier below is operating at a frequency of 60 Hz, and the RMS value of the transformer output voltage v, is 6.3 V. (a) What is the value of the dc output voltage Vo (the peak V.) if the diode voltage drop is 1 V? (b) What is the minimum value of C required to maintain the ripple voltage to less than 0.25 V if R = 0.50? (c) What is the required PIV rating of the diode in this circuit? (d) Sketch the output waveform labeling Vpeak (the dc value), Vripple, and sketch the general shape of the diode current Ip below the voltage waveform. + D1 R
1. Compare the output waveform for Half-Wave Rectifier with and without capacitor. Compare the output waveform for Full-Wave Bridge Rectifier with and without capacitor.
3. For the half-wave rectifier given in the figure below, find the average values ofthe output voltage and current, and the ripple factor of the output voltage.
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
. In a centre tapped full wave rectifier with a capacitor compared to ½ wave rectified DC - what will be the resulting: A. Amplitude ripple B. Frequency C. Mean DC Output
S-2) a) On the bridge type full wave rectifier circuit given in the figure Plot the current paths for each of the +/- alternans. b) The waveform of the Vç output voltage is given in the graphs on the side. Draw it in the blank and calculate the peak value and indicate it in the graph. c) Calculate the effective value of the output voltage. (Vç (eff) =… ..?). Note: Diodes are not ideal. VD = 0.7V.
Question 1: a) Draw the circuit diagram and explain the working of Half Wave Rectifier (HWR). b) With the help of a neat circuit diagram, explain the working principle of a Centre tapped Full Wave Rectifier. Also, Draw the expected output voltage wave forms with/without using a capacitor parallel with the load. Show the factors affecting voltage ripples and how to eliminate these ripples as much as possible.
04: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10°t)] rms input signal has a loud resistor of 3.3k0. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VLp) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ? 4. What is the de valtage available at the load? 5. Explain who could filtering output signal. 6. Draw circuit that give opposite out waveform. 7. Why connect circuit in this form.
(ii) Briefly explain the principle of operation of the rectifier circuit. Ensure to explain about the pair of diodes that conduct for the positive cycle and the pair that conducts for the negative cycle of the input signal. (iii) Suppose the input signal vs(t) is a sine wave with a peak voltage of 8 V and frequency of 50 Hz. Sketch the output signal across the load resistor R₂ with the expected peak voltage. Also state the ripple frequency beside the waveform. (iv) Explain why there is a short period between pulses when the output voltage is zero.