4- Describe the effect of increasing the clock frequency on the integrator output in the DM system. 5- Describe the effect of increasing the input signal amplitude on the integrator output in the DM system. 6- If an input analog signal x(t) = 2 cos(2tx1000r) is to be transmitted via a delta modulator having a step-size A = 1V, then find the minimum sampling frequency f, in order to avoid the slope overload distortion.

4- Describe the effect of increasing the clock frequency on the integrator output in the DM system. 5- Describe the effect of increasing the input signal amplitude on the integrator output in the DM system. 6- If an input analog signal x(t) = 2 cos(2tx1000r) is to be transmitted via a delta modulator having a step-size A = 1V, then find the minimum sampling frequency f, in order to avoid the slope overload distortion.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

B- An rate. analog signal having single frequency as 3 kHz is sampled with 5 kHz S Describe its frequency spectrum. What will be the output if the sampled signals a passed through a low-pass filter having cutoff frequency at 2.5 kHz? signal. are sent in the analog
A PM signal has a maximum allowed deviation of 17 kHz, and an actual deviation of 8 kHz. What is thepercentage modulation?
Or Lhe value *7. Suggest an A/D converter where the length of the sampling gate is directly proportional to the analog voltage but the frequency of the clock being counted by a converter is fixėd.
3. (a) The following figure depicts a sampled analog signal for digital signal representation. By applying the concept of Pulse Code Modulation, assume there will be 4-bit code words for each sampled amplitude. Calculate the normalized PAM value and normalized quantized value for the given analog signal value at different time stamps . Assume that the sampling amplitudes are between -32V to +32V. Time Analog Signal Value (V) -10.8 1 14.5 30.6 -21.7
Two low pass signals, each band limited 4 KHz, are to be time multiplexed into a single channel using PAM. Each signal is impulse sampled at a rate 10 KHz. The time multiplexed signal waveform is filtered by an ideal LPF before transmission. (a) What is minimum clock frequency of the system? (b) What is the minimum cut off frequency of the LPF? Ans. (a) 20KHz (b) 10KHz
4. Signal conditioning element basically takes the output of the sensing element and converts it into a form more suitable for further processing, usually in the form of a DC voltage, DC current or variable frequency AC voltage. The output of the sensing element is usually too small to operate an indicator or a recorder. Therefore, it is suitably processed and modified in the signal conditioning element so as to obtain the output in the desired form that is amplify the signal and filtering the unwanted signal. i. Describe the aliasing phenomenon. ii. Suggest a solution to minimize the effect of aliasing.
A sinusoidal signal of 2 kHz frequency is applied at the input of a delta modulator with a step size of 0.1 volt. The sampling rate of the delta modulator is 20000 samples per second. What will be the maximum amplitude of the sinusoidal signal if there is no slope overload distortion?
d. flatline 6. Continuous time signal sin (3m) is sampled at a rate of 4 samples per second. At what sample output value reach to peak value (+1V)? Hint. Simulate with sample index n = 0 to 20 samples. a. n=0 b. n 6 C. n 12 d. n= 4
3 ) Time taken for the output signal rise to 95% from 10% is called rise time Select one: True False
Signal and system problem plz explain every step with a formula
| 2-Consider the following analog waveform.This waveform is to be sampled at a 1-kHz rate and quantized with a 3-bit quantizer (input voltage range is -1.0 to +1.0 V). (a) ) What is the resolution of this quantizer? (b) p) On the graph, circle the sample points on the analog waveform below. Note that the time axis is in msec. (c)() On the graph, indicate the quantization intervals and corresponding digital words. (d) ) On the graph, indicate the digital word assigned to each sample point. (e)() When a receiver receives the transmitted bits, D/A is used to recover the analog signal, but the recovered signal is not the same as the original analog signal. What is the term to describe this difference and what can be done to minimize this difference? 075 0.5- 025 025 0.5 075 10 time (msec) W oprajjdwe
Identify the given statement. FM and PM demodulators can actually reduce noise and increase the signal-to-noise ratio during the demodulation process by using limiters. This is known as the capture effect. Select your answer. The statement has no fixed information. The statement is false. The statement is true. The statement is a case-to-case basis.