4- Aircraft structure is affected by some factors which cause typical damages.. Please correlatefactors and damages on the colunmns below:Factors1. Repetitive loads2. Time (calendar)3. Wear and tearDamagesa) Corrosionb) Accidental damagesc) Fatigue

The typical damages in Aircraft structures are due to fatigue, corrosion, wear and tear in the…

Answered: 4- Aircraft structure is affected by…

4- Aircraft structure is affected by some factors which cause typical damages.. Please correlate factors and damages on the colunmns below:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1- Select the optimum choice for: high speed air craft skins material. Table 1: The properties of metallic materials E, GPa Max. use lemp, 'C | Density, Mg/cm' ay, MPa | Relative cost per unit sheet area Material 2.8 300 2 Aluminum alloy 200 69 200 7,8 350 350 700 Carbon steel Stainless steel 193 7.8 650 6 8.9 600 6 Nickel alloy Titanium alloy 207 1000 116 600 4.5 900 10 Table 2: Weighting factor Specific yield strength: Max, use temperature: Youngs modulus: 4 2
When an object is placed underwater, the pressure on the object is subjected to uniform stress on all sides. a) define volume strain, the bulk modulus, compressibility, and the relationship between the bulk modulus and compressibility. b) A 100 litre volume of liquid is subjected to a 2000 psi increase. If the compressibility of the liquid is 5 x 10-5 per atm, find the bulk strain and absolute decrease in the volume of the liquid c) explain the concepts of shear stress and shear strain? could these concepts be applied to the fluid problem above?
19) Fatigue test results of a material are shown in the diagram. a) Estimate the ultimate static strength of this material b) Estimate the fatigue (endurance) limit. c) If this test specimen has a cross-sectional area of 14 cm² and subjected to a maximum repeated load of 2800 kg over it, after how many repetitions will it fail? d) Determine the fatigue strength at 1000 cycles o (kgf/cm³) 500 400 300 200 100 0 1 2 3 4 5 6 7 log1o N
The Stress-Strain diagram is plotted to study: a) Material's response b) Material's behavior C) Material's properties d) All of the above
The fatigue data for a ductile cast iron is given in the table below. Stress Amplitude [MPa] 248 236 224 213 201 193 193 193 Cycles to Failure 1 × 10³ 3 x 105 1 x 106 3 x 10° 1 x 107 a) Create a S-N curve from the data. b) What is the fatigue limit for this alloy? c) Determine the fatigue life at 230 Mpa and 175Mpa d) Determine the fatigue strength at 2x105 and 6x106 cycles 3 x 107 1 × 108 3 x 108
1. Consider the temperature in a composite wall consisting of materials A,B,C which is shown below. Three materials' sizes are exactly equal. Top and bottom side of the wall is well insulated. We assume that thermophysical properties are all constant. Which two of the following are true A) Thermal resistance is largest in material A B) Theral resistance is largest in material B C) Heat is being generated within the wall D) Sign of heat rate is positive E) sign of heat rate is negative 2. Which two of the following are best correct statements for the wall with the temperature distribution shown below: A) The heat flux would be constant at any location in the wall B) It is unclear if heat is being generated within the wall C) Heat does not flow across the centerline D) Everywhere inside the wall, heat flows only to the right( same direction as the x-direction E) If the convection outside the wall is occuring with a normal magnitude of h, then it can be expected that Ts >>…
Mechanical Engineering The fatigue strength limit Sn (n = 106) of a steel part is 112 MPa and its ultimate tensile strength (Sy) is 385MPa. Adopting Ct = 1, and S103 = 0.9 * Su* Ct, determine: (Use two decimal places in the answers), (* is multiplication signal): a) The fatigue strength (in MPa) corresponding to a life of 40000 cycles. b) The average life in cycles that this part would last if subjected to an alternating stress of 170 MPa due to bending.
The following graph shows a load-extension graph from a test on a polymer specimen 15mm in diameter and 45mm long. The rightmost datapoint represents the reading at the point of fracture. Load (KN) 20 15- 5- 0.2 0.4 Extension (mm) 0.6 a) 0.2% offset yield strength b) The tensile strength c) The modulus of elasticity 0.8 F Determine the following physical properties. Show all your working and express all your answers in appropriate Sl units where appropriate: 1.0 d) The % elongation e) The engineering stress at fracture f) Estimate the modulus of resilience
a) b) Find the time constant associated with this transient analysis. Enter only a numeric value (with no units entered) and express your answer in units of seconds. c) Find the time it takes for the temperature of the wire surface to reach a temperature that is within 2∘C of the steady-state temperature of the wire. Enter only a numeric value (with no units entered) and express your answer in units of seconds.
Case Study Determine Properties from Tensile Test Data A cylindrical specimen of stainless steel having an initial diameter of 12.8mm and initial length of 50.8mm is pulled in tension. Use the data provided below to a) Plot the data as engineering stress versus engineering strain using excel or similar software. b) Compute the modulus of elasticity. c) Determine the yield strength at a strain offset of 0.002. d) Determine the tensile strength of this alloy. e) What is the approximate ductility, in percent elongation? f) Compute the modulus of resilience. Load (N) Length (mm) 50.800 12,700 25,400 38,100 50,800 76,200 50.825 50.851 50.876 50.902 50.952 89,100 92,700 51.003 51.054 102,500 107,800 119,400 128,300 149,700 159,000 160,400 159,500 151,500 124,700 51.181 51.308 51.562 51.816 52.832 53.848 54.356 54.864 55.880 56.642 Fracture
b) A sedan car weights 2100 kg with 45:55 distributions front to rear. The car has wheelbase of 1.9 m. With aid of following table showing the tyre cornering stiffness values for different loads: Load Cornering Stiffness (kg/deg) 300 131 400 149 500 174 600 203 i) Calculate the cornering coefficient for the front and rear tyres. ii) Calculate the understeering gradient. iii) Determine whether it is understeer or over steer. iv) Calculate critical or characteristic speed.
mass-spring-damper system with one degree of freedom is exposed to vibration under the influence of a harmonic force. In my system, it is given as m=2 kg, k=800 N/m, c=64 Ns/m. The amplitude of the harmonic force is Fo=256 N and its frequency is w= 20 rad/s. Answer the questions in options a, b, and c according to the given information. a)a-)Calculate the damping ratio of the system b)Calculate the magnification factor (M) of the system C)Calculate the maximum vibration amplitude (X) (meters