26 PA PB Water Water Oil Manometric fluid Manometric fluid Find the pressure difference at two points A and B in the pipe carrying water at 293K and connected to a mercury differential manometer and also has oil filled in between it. Take p(Hg) 13 600 ka/m^3 and = 700 ka/m13 1.20 m I 09'0 0.72 m 0.08 m

26 PA PB Water Water Oil Manometric fluid Manometric fluid Find the pressure difference at two points A and B in the pipe carrying water at 293K and connected to a mercury differential manometer and also has oil filled in between it. Take p(Hg) 13 600 ka/m^3 and = 700 ka/m13 1.20 m I 09'0 0.72 m 0.08 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2/ A fluid containing (water, oil, sand) flowing through the tube and open to the atmosphere as shown in the figure below.. Note that p°- 1.013*105 Pa Calculate the absolute pressure (Pa). Density: Pwater = 1000 kg/m Pail = 800 kg/m Pand = 200 kg/m P. h3=12 cm hg al2cm oIL Pa h25 cm ng = 6 cm %3D Sand water
Find the difference in pressure head and velocity of flow of an oil through a pipe, when the difference of mercury level in a different U-tube manometer connected to the two tappings of the pitot tube as 110 mm. Take co-efficient of the pitot tube ("L" shaped measuring instrument ) as 0.9 and sp. gr of oil = 0.9Difference in pressure head (unit in m) =Velocity of flow (unit in m/s) =
Find the difference in pressure head and velocity of flow of an oil through a pipe, when the difference of mercury level in a different U-tube manometer connected to the two tappings of the pitot tube as 112 mm. Take co-efficient of the pitot tube ("L" shaped measuring instrument ) as 0.92 and sp. gr of oil = 0.8 %3D (Enter only the values in the boxes by considering units given in the bracket. Do not send the hand written answers to my mail Id) Difference in pressure head (unit in m) = Velocity of flow (unit in m/s) =
Show complete solution with diagram: A 3.81-cm diameter venturi meter is installed in a pipe with an internal diameter of 10.23 cm. A 127 cm manometer filled with mercury is used to measure the pressure difference across the venturi meter. If the manometer reads 101.6 cm when 15 °C water is flowing through the pipe, what is the flow rate of water (m3/min)? Assume that the venturi meter coefficient of discharge equals 0.98.
Find the difference in pressure head and velocity of flow of an oil through a pipe, when the difference of mercury level in a different U-tube manometer connected to the two tappings of the pitot tube as 108 mm. Take co-efficient of the pitot tube ("L" shaped measuring instrument) as 0.9 and sp. gr of oil = 0.8 Difference in pressure head (unit in mm) = Velocity of flow (unit in km/hr) =
You are evaluating a pipe network transporting water from a large river reservoir to the citywater storage facility. According to the pipe specifications, the pressure leaving the pipe network(continuing to city storage) cannot exceed 3 psi. Given Qa, pipe diameters (Da – Dd), determinethe pressure exiting the pipe network. Do the city designers need to reconfigure the set-up. Usethe Hazen-Williams equation to determine the head losses. All pipe lengths are 200 feet long,and the pipes are made of recently installed galvanized iron. given below Flow rate and Diameter for all 4 pipes: Q_a=42 csf, D_a=4ft, D_b=3.2ft, D_c=7ft, D_d=2.1ft.
Apply Bernoulli equation in solving the problem: A 3.81-cm diameter venturi meter is installed in a pipe with an internal diameter of 10.23 cm. A 127 cm manometer filled with mercury is used to measure the pressure difference across the venturi meter. If the manometer reads 101.6 cm when 15 °C water is flowing through the pipe, what is the flow rate of water (m3/min)? Assume that the venturi meter coefficient of discharge equals 0.98.
The pressure (p2) of water in the pipe is equal to: (Assume aj = az = 1) Elevation = 100 m P2 = -9.81(80 ++ hịoss) kPa а. 2g b. P2 = 9810(80 + + hjoss) kPa %3D 2 Elevation = 20 m P2 = 9.81(-80 + hjoss) kPa 2g C. %3D d. P2 = 9.81(80 – 2g – hjoss) kPa - L= 2000 m
y aer. A Pitot tube is used to measure the air flow rate in a eircular duct 8.5 m I.D. The "riowing air temperature is 65.5°C. The Pitot tube is placed at the center of the duct and the reading R on the manometer is 1.2 cm of water. A static pressure measurement obtained at the Pitot tube position is 2.0 cm of water above atmospheric. Take Cp 0.98,9ter ase press u = 2.03 x 10 Pa.s, if U- Ux ( 1-0.17). Calculate The velocity at the center and the average velocity. The volumetric flow rate of the flowing air in the duct
Amé — Today at 3:32 PM The flow rate of water of mass density of 998 kg/m^3 and viscosity of 1.002 x 10^-3 kg/m-s, through a 600 mm diameter pipe is measured with an orifice meter withj a 300 mm diameter opening to be 400 L/s. Determine the pressure difference indicated by orifice meter if Cd=0.61. a. 40.3 kPa b. 50.3 kPa c. 20.3 kPa d. 30.3 kPa
Fundamental of fluid flow: A venturi meter with a throat diameter of 6 cm is fitted in a horizontal pipeline of 12 cm diameter with oil of specific gravity 0.88 flowing from left to the right. The difference in level in the two limbs of a mercury manometer connected to the tapping points read 12 cm and the connecting pipes are filled with the same oil. (a) If two pressure gauges are fitted at tapping points, one at the throat and the other in the inlet. Determine the difference between the 2 gage pressure readings in kPa. (b) Determine the flow in m^3/s neglecting head losses.
An oil of specific gravity 0.9 is flowing through a venturimeter with inlet diameter of 300 mm and throat diameter of 205 mm. A differential manometer connected to the inlet and throat of the venturimeter gives a difference in the reading of 27 cm of mercury. Take coefficient of discharge of the venturimeter (Cd) as 0.96. Find the following Inlet area of the Venturimeter (in m2) Answer for part 1 Throat area of the Venturimer (in m2) Answer for part 2 Differential pressure head 'h', (in m of oil) Answer for part 3 Discharge of oil through Venturimeter (in m3/s) Answer for part 4 Discharge of oil through Venturimeter (in Litre/s)