- 0.05-The circuit shown in the figure consists of resistance, capacitance and inductance in serieswith a 100V source when the switch is closed at t = 0. Find the equation obtained from thecircuit in terms of current.0.OSH100v`20uFa) 100 = 201 + 0.05 4 +di10- S idtdt20x10-b) 100 = 201 – 0.05 +20x10-S tdtdec) 100 = 201 + 0.05 tdi120x10-S idtded) 100 = 201di20x10-J idt

Answered: Image /qna-images/answer/29d0d8b9-33b5-499f-87ca-5fcd510029ab.jpg

Answered: 20 0.OSH 100v 20uF a) 100 = 201 + 0.0s…

Engineering

Electrical Engineering

20 0.OSH 100v 20uF a) 100 = 201 + 0.0s de ;Sidt 20x10-

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Related questions

Q: Chapter #3 Oscillators HW # 1 Find R and the frequency of operation [rad/sec] for the circuit below:…

Q: What will be the % Error if the ratio of Actual Value over Expected Value (AV/EV) = 0.98? O a. 20% O…

Q: Refer to Figure below. For midpoint biasing, lp would be + 20 V Vin # 0.1 µF 7.5 mA 10 mA. 2.5 mA 5…

A: We need to find out mod point biasing current for given circuit

Q: Solve for alpha(a) collector current is 6.236mA and emitter current is 6.292mA O 0.9219 O 0.9901 O…

Q: ESH ANALYSIS 60 40 30 |1 12 13 19 + | U9

Q: Figure 20-13 L, = 50 mH V = 120 VAC f = 15.915 kHz L = 100 mH %3D 150 mH

A: Given: Frequency of operation, voltage, inductance Calculate: Leq,XLeq, V,i

Q: Assume beta = 100, V = 0.7 V, V = OV. BE CE,sat a. If R = 0 and V = 3 V, determine the value of V.…

Q: 3V analog output is equivalent to diğital input word 011. Select one: True False

Q: For the circuit shown in Figure above, the * value of current I will be 20 20 60 120 100v 60 10A O…

Q: Assume beta = 100, V = 0.7 V, V = OV. BE CE,sat a. If R = 0 and V = 3 V, determine the value of V…

A: The solution is given below

Q: Use any analyzing method to obtain the value of lo 20 ww $/0 A -20 -120 20 1.

Q: 6. Find the total resistance 20 60 at Rab- 20 30 20 30 30 60 60 20

Q: How many select lines are there in a 1:64 demuc?

A: A demultiplexer (DEMUX) is a digital circuit which has one input and many output terminals. Using…

Q: 4. In JFET self bias the Ip vs VGs load line is a O line at a slope of 45° O vertical line O line…

Q: Question 30 Solve for beta(5) collector current is 6.236mA and emitter current is 6.292mA. O 114.16…

A: This question belongs to analog electronics . It is based on the concept of relation among base…

Q: Q.1: Draw the output voltage of the circuit shown below, if the input voltage 14Sinwt. E D Vị V.…

A: The diode is ON when the voltage across anode is more than the cathode voltage. It is known as…

Q: Use Millman's Theorem to solve for output voltage, Vo. Ans. Vo=—0.5V

Q: 20Ω Α -40Ω Β 10Ω 30Ω 50Ω

A: The solution is given below

Q: The transistor in the shown figure has the following values : VBE=0.7 V, af-0.98. c) Insert an AC…

A: Considering the dc biasing,

Q: FIGURE 11.33 The state transition diagram for a design problem. 11/1 00 10 10/0 10/1 11/0 01/0 01/0…

A: The state transition diagram for a design problem,design a sequential circuit using T flip flops.

Q: The ideal case for VSWR for matching condition is 2 0 1 infinity O

A: The ideal case for VSWR for matching condition is 1.

Q: Use of lag compensator in a system will increase the rise time of the system. Select one: O True O…

A: By using lag compensator type of system increase by 1

Q: Compute ID for the following cases, You can use Kp=Kn= 20U 1. VSG= 4V, VSD = 4V, VTP= -1V 2. VSG=…

A: Drain current

Q: Find vc, ik, and vx for t20 when: 1. vc(0') = 20 V 2. v,(0*) = 20 V 8 Ω ix 5Ω 0.1 F VC 12 Q Vx +

A: In this question we need to find a VC , Vx and Ix for t>0.

Q: Q.1: Draw the output voltage of the circuit shown below, if the input voltage 14Sinwt. E D Vi Vo…

A: The diode is ON when the voltage across the anode is more than the cathode voltage. It is known as…

Q: シ Br Bexyで, fd ditad frua lawving the sufuce

A: Total flux pussing through any closed surface is equals to charge enclosed by that surface.

Q: ured output voltage is ec L: 0.0001 A V: 10 C: 200e-6 R: 4 DutyCycle: 0.3

Q: A common emitter amplifier has Cbc = :4pF, Cbe= 10pF and re = 50 Q. Calculate the value of Cin if…

Q: 1. Explain the operation of the circuit below. Include a description of its output waveform,…

A: Referring to the given circuit, op-amp A is inverting amplifier and the op-amp B is comparator.…

Q: Quèstion 11 The current gain(a) is greater than the current gain(B). True False this res ponse

Q: a. r'e b. Rin Base c. Rin Total d. A (The ac voltage gain) 10 µF V₂0H M 22 V 56 ΚΩ 8.2 ΚΩ 1.5 ΚΩ…

Q: Determine the dc parameters le, Vc, Ve, VB, and VcB when B = 100 using the BJT circuit below. VEe +…

A: Given circuit: Here β=100 To find: The DC parameters IE, VC, VB, VE, and VCB.

Q: Current Plot 150 125 100 75 50 25 5. 10 15 20 25 Time (msec) Current (mA)

A: In this question we will find effective current...

Q: Q.1: Draw the output voltage of the circuit shown below, if the input voltage 14Sinwt. E D 6.2V Ge…

A: The diode is ON when the voltage across anode is more than the cathode voltage. It is known as…

Q: Find the ralue of Vo, LI, i2 and i Vo Si 0.47K 20v Ge 21kQ Si 0-47 K is

A: To find the voltage or current of a circuit that contains more than one diode, it is important to…

Q: From the circuit given below, determine the output voltage (Vo). 190k, ww 1,0k ww 2mV 5k Vo 3mV 3k

A: In this question, we need to determine the output voltage Vo. We are solved this problem using the…

Q: 2. What range of output voltage is developed in the circuit of Fig. 10.67 ? V-0.1 V 200 A2

A: 2) Non- inverting amplifier output voltage,V0=1+RFR1V1

Q: base cont tion (re model), an ac signal of 10 mV is applied, resulting in an ac emitter current of…

A: We need to select correct option for current gain

Q: 5. What output voltage results in the circuit of Fig. 10.66 for an input of V,=0.3 V? V1 Vo 360 k2…

Q: Use Kirchoff's junction rule to give the equations of current in figure. 30 20 40 50

Q: Design the circuit in the figure such that IC = 1.5x10 ^ -3A and VC = 3.5V, suppose β = 90

Q: If the value of dc alpha is 0.9, then the value of dc beta of a transistor is O 900 O 90 O 0.9 9.

Q: Qz Find the output resuase if the frequen@yvesponse of the System is for the following 2+jw input:…

A: To find the output response of the system if the frequency response of the system is given by H(w)…

Q: Determine the Q point of the transistor circuit shown in Figure. Given B = 200 and VBE = 0.7V. Ic IB…

Q: Question 1: b) Determine DC output voltage without a capacitor. +40 10 ms 22 ka 19 -40 22M2 22 2

A: Diode will conducts when anode voltage is greater than cathode voltage and ideal diode maintains 0…

Q: Q-6) Calculate the output voltage for the circuit given below: 2ΚΩ 4 KO 8KQ 2 V "Vo -1 V• 3 KQ 1 KQ

A: In this question, Find the output voltage Vo. We are solved this problem using the virtual…

Q: Consider the same circuit with the same component values. B = 99. Vcc = 10V, / = 2mA, R1 = 50k2, and…

Q: 5- Compute DTFT for the following sequence: 0snsM w[n] O.w.

A: The time domain signals can be continuous or discrete. The time domain signals can be periodic as…

Q: Determine the parameters of point Q b. Draw the equivalent circuit in AC c. Calculate the voltage…

Question

100%

- 0.05-
The circuit shown in the figure consists of resistance, capacitance and inductance in series
with a 100V source when the switch is closed at t = 0. Find the equation obtained from the
circuit in terms of current.
0.OSH
100v
`20uF
a) 100 = 201 + 0.05 4 +
di
10- S idt
dt
20x10-
b) 100 = 201 – 0.05 +
20x10-S tdt
de
c) 100 = 201 + 0.05 t
di
1
20x10-S idt
de
d) 100 = 201
di
20x10-J idt

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
An inductance coil consumes 500W of power at 10A and 110V and 60HZ. Determine the resistance and the inductance of the coil
A series R–L–C circuit comprises a 5µF capacitor, a 4ohm resistor and a variable inductance L. The supply voltage is 10∠0◦ V at a frequency of 159.1 Hz. The inductance is adjusted until the p.d. across the 4 ohm resistanceis a maximum. Determine for this condition (a) the value of inductance, (b) the p.d. across each component and (c) the Q-factor of the circuit.
A 22-k resistor and a 0.02-F capacitor are connected in series to a 5-V source. How long will it take the capacitor to charge to 3.4 V Select one: a. 0.501 ms b. 0.66 ms c. 0.44 ms d. 0.70 ms
C5 What is the correct explanation for the voltage seen at Va in Figure C5? Va 1 Sost We will assume that the Vout Out Vb, capacitor is charged to a value determined by the feedback and the supply voltage +BVsat. Figure C5 A. The waveform on the capacitor looks like a discharge, and then a charging waveform to an equal but opposite magnitude voltage, B. The capacitor simply reverses its charge, with a charging waveform, C. The capacitor simply reverses its charge, with a discharging waveform, D. None of the above.
CONSIDER THE CIRCUT BELOW.SUPPOSE V1=10V AND V2=1V BEFORE THE SWITCH IS CLOSED,WHAT IS THE COOMN VOLTAGE ACROSS THE CAPACITOR AFTER THE SWITCH CLOSED.
In the figure ɛ = 10.0 V, R1 = 4.00 N, and R2 = 1.00 N. The inductor is ideal. If the switch is closed for a long time, what is the current through the inductor. Give your answer in A. Şekildeki devrede ɛ = 10.0 V, R1 = 4.00 N , ve R2 = 1.00 N olarak verilmişlerdir. Solenoidin iç direnci yoktur. Anahtar kapatıldıktan çok uzun süre sonra solenoidden geçen akım A cinsinden nedir. R1 R2 L E Yanıtınız
A resistor of 20ohms and a capacitance of unknown value when connected. In in parallel across a 100V, 50Hz supply take a current of 6A. The combination is now connected across a 100V supply of unknown frequency and the current falls to 5.5A . What is the frequency?
Using the series circuit in Figure 3 consisting of a voltage source V, the resistor R and the fully uncharged capacitor C, how to find the value of the capacitance C considering as known data the time constant of the circuit T and the value of the resistor R? V ww R
The figure below shows a simple RC circuit with a 3.30-μF capacitor, a 4.40-M resistor, a 9.00-V emf, and a switch. What are the following exactly 9.00 s after the switch is closed? (a) the charge on the capacitor 13.7204 UC (b) the current in the resistor 0.0110522 x Your response is off by a multiple of ten. HA (c) the rate at which the capacitor is storing energy μW (d) the rate at which the battery is delivering energy μW