2. Write any two types of belt drives with neat diagram and it's any industrial applications?

Q: When minimum space is an important requirement, the best type of mechanical connecting device for…

A:

Q: a V-belt depends on the rotational speed of the smaller pulley.

A: In belt drive power transmission depends on following factors 1 linear velocity of velt 2 tension of…

Q: What is the distance between the axles of the two pulleys?

A: Given that: diameter of smaller pulley = 250 mm diameter of larger pulley = 500 mm wrap angle = 120…

Q: Q5: What kinds of Belt drives with explanation one only.

A: Belt drive: The belt drive is a flexible mechanical system which is used to transfer the power from…

Q: 5. What type of motors are used in robotics application? Explain the operation with diagram how a…

A: Proper selection of motor in robotics is very important because improper selection may result in…

Q: Find out degree of freedom? show number of link and joint

A:

Q: Explain the parameters that help to make the driveshafts lighter and efficient

A: Aluminum driveshafts are great for a few reasons. First, they're a lot stronger than the stock…

Q: Belt and rope drives are the examples of ______________  under classification of kinematic pair.…

A: Belt and rope drives are examples of which pair

Q: Name and describe the two principal types of conveyor holdbacks

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: What is the length of a belt that is used for a 4” pulley and a 10” pulley that have a center to…

A:

Q: Define the following with formula and units. a) Torque b) Couple

A:

Q: write discussion about to determination of the capacity of a belt conveyor.

A:

Q: Make a Drive Shaft in SINUMERIK (ste

A: A drive shaft is a vehicle shaft that transmits power from the transmission to the wheels. The…

Q: (1)Explain all the parameters that will be helpful to make driveshaft more efficient and…

A: Purpose of the drive shaft :-  The torque that is produced from the engine and transmission must be…

Q: (a) Explain how to calculate the initial tension for a V-belt drive.

A: Assume, The initial tension in the belt = To The tension in the tight side = T1 The tension in the…

Q: With a neat sketch explain the Analysis of simple hydraulic Jack

A:

Q: What are the factor considered in belt drives while transmitting the power from one pulley to next…

A: The transmission of power from one point to another is done by mechanical mechanisms. If the…

Q: Write down the names for parts in chain drive?

A:

Q: he belts and rope drive is one of the links which is aving in Es link.

A: Which type of pair in belt drive.

Q: Make a schematic representation of the links for the backhoe mechanism only and find its mobility

A: The schematic representation of various links and joins are required. Also we need to obtain the…

Q: O Write down the names for parts in chain drive?

A: Given:- Structure of chain drive   To find:- Parts name

Q: Product of radii of belt drivens to product of radii of belt drives is speed ratio

A:

Q: A cross belt drive has a 6 in. pulley driving a 48 in. pulley. The distance between their centers is…

A:

Q: What is Belt-conveyor system?

A: The belt conveyor system is essential in a material handling industry. It is used to transport bulk…

Q: In a V-belt drive, which of the following is true about the groove angles of the sheaves, given the…

A: We can answer first question since the exact one is not specified. Please resubmit the question by…

Q: speed of the motor in RPM for which the mobile

A: Given data; Mobile phone has a small motor with an eccentric mass used for vibrator mode which data…

Q: Derive the equatlon that describes the relationship between the tight and slack tenslon in V- belt…

A: The correct tension is the lowest tension at which the belt will not slide or scream when…

Q: 3. With a neat sketch explain the Analysis of simple hydraulic Jack.

A:

Q: /5 --- A computer cannot "boot" if it does not have the

A: An operating system is the system software that handles the software and hardware resources and…

Q: When rope drive is preferred?

A:

Q: .Explain belt driven starters and mention its advantages

A: Belt driven starters A belt driven starter motor system used to start an internal combustion engine.…

Q: What type of motors are used for conveyor system? Explain the operation of conveyorsystem with…

A: AC induction motors are ideal for conveyor systems that operate continuously in one direction. For…

Q: Find the angle of contact on the small pulley for a crossed belt drive with center distance of 73",…

A:

Q: Derive the equation of angular velocity ratio of and effect of slip for Flat belt drives with neat…

A:

Q: Q. No 1. drawing and stepwise procedure. Also find the expression for the Length of the belt drives…

A: The expression have been derived and has been attached.

Q: conveyor

A: given: Explain stationary and movable trippers of belt conveyor

Q: A belt-driven blower assembly is equipped with a motorthat turns a 5-in. drive pulley at a speed of…

A:

Q: A- Draw a detailed schematic of a PUMA robot (show all joints, axes of  motion and link lengths)?…

A: PUMA stands for :  Programmable Universal Machine for Assembly

Q: Can you derive the equation of the length of the belt and the angle of wrap between belt and pulley…

A: We have to explain about open and cross belt drive length

Q: drive?

A: given: What is open belt drive?

Q: What are the factor considered in belt drives while transmitting the power from one pulley to next…

A: The factors considered in the belt drives while transmitting the power from one pulley to the other…

Q: For a four bar linkage in toggle position, The value of mechanical advantage is??

A: GIVEN DATA FOUR BAR MECHANICSM IN TOGGLE POSITION GIVEN WE HAVE TO TELL MECHANICAL ADVANTAGE OF IT

Q: Explain all the parameters that will be helpful to make driveshaft more efficient and lightweight.

A: There are several factors that go into driveshaft selection. In order of importance, they are…

Q: Task 3 (a) Explain how to calculate the initial tension for a V-belt drive.

A: Since you have asked multiple question we will solve first question for you if you want a specific…

Q: the advantages, disadvantages and applications of ball bearings

A: Application : it can handle axial and radial thrusts but can not handle very high weights Elevators,…

Q: A So Find tension in AC and BC Hoola

A:

Q: Discuss briefly the various types of belts used for the transmission of power.

A: Solution:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.