2. What are the considerations in choosing a manometric fluid for the measurement of pressure drop for a flowing fluid? The pressure drop measured in turn is related to the flow rate of the flowing fluid. Talk about these parameters: density (You may include graphs you made from the simulator data to prove your point) boiling point price and avalability solubility/miscibility with common industrial fluids toxicitylenvironmental footprint

2. What are the considerations in choosing a manometric fluid for the measurement of pressure drop for a flowing fluid? The pressure drop measured in turn is related to the flow rate of the flowing fluid. Talk about these parameters: density (You may include graphs you made from the simulator data to prove your point) boiling point price and avalability solubility/miscibility with common industrial fluids toxicitylenvironmental footprint

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3. a) List and describe the suggestions of two major assumptions of the lumped capacitance method. b) For quick response of a thermocouple to observe varying temperature of fluids which one of the following suggestions is correct. Explain your answer by giving the reasons. )Diameter must be large i) surface heat transfer coefficient must be large Bi <0.1 iii)material specific heat must be large iv)material density must be large
What are the primary dimensions of electric voltage (E)? (Hint: Make use of the fact that electric power is equal to voltage times current.) When performing a dimensional analysis, one of the first steps is to list the primary dimensions of each relevant parameter. It is handy to have a table of parameters and their primary dimensions. We have started such a table for you in which we have included some of the basic parameters commonly encountered in fluid mechanics.add to this table. You should be able to build up a table with dozens of parameters
1... Why do we use round-shaped coils (I.e., Round shaped turns in the coils) in both the primary and secondary circuits [If those coils were not round-shaped, what would be the problem]? Must show the draw figures 2.... Write down major differences between conducting and displacement current densities with proper figures.
A solenoid of 100 turns has a length of 75 cm and the radius of 20 cm. A steel rod of circular cross-section is fitted in the solenoid coaxially. Relative permeability of steel is 3000 and a dc current of 10 A is passed through solenoid. Conclude the inductance of the system, energy stored and the mean flux density inside the solenoid.
You have developed an idea for using a poly Si surface‐ micromachined cantilever. Initially, you designed a process flow for creating this simple structure, and the process flow is detailed in the figure below. ( cross section view and top view)There are several critical errors with this process (things that won’t work or won’t produce the result). Please find the critical errors in this process flow and, where possible, suggest alternate approaches. Do not worry about the accumulation of errors, but rather treat each step assuming that the structure up to that step could be created.This structure is actually quite simple to make. Develop a simpler process flow and associated masks to create the final structure. Be sure to show cross‐sectional and planar views of all key steps in the process.
Division: Elctronic Eng. Subject: Energy conversion I Year : Second Q1/ A / Discuss B-H curve of a ferro-magnetic material . B / Define the following terms (any three) : (i) MMF (ii ) magnetism. (iii ) Reluctance (v) flux density Q 2 A magnetic circuit has the mean length of flux path of 20 cm, and cross sectional area of 1 cm?. Relative permeability of its material is 2900. Find the mmf required to produce a flux density of 2 tesla in it. If an air gap of 1 mm is intro gap as a fraction of the total mmf to maintain the same flux density. luced in it, find the required the air
Create two problems about Steady-State Heat Flow – Heat Convection in Fluid, and write your solutions. Thank you!
Give realtive relations between and relative parameters for the following: 1.) ohmic resistance 2.) ballistic transport 3.) quantification of conductance
4) We usually think of wires as perfect (R=0) conductors, which is not quite accurate. Real wires have resistance albeit small - usually less than an ohm. With this in mind: a. Consider a uniform cylindrical copper wire that has diameter of 1 mm and is 10 m long. What is the resistance of this wire? The resistivity of copper is 1.72 x 10-8 9-m. b. This wire is cut in half, and the two strands are used to connect an electric heater to an outlet supplying 1500 W at 120 V. Draw a simple circuit diagram, including the voltage source, resistances of the connector wires, and the calculated resistance for the heater. C. How much of the total 1500 W is absorbed by the connector wires, not by the electric heater? d. If the specific heat and density of copper are 385 J/kg°C and 8940 kg/m³ respectively, how much will the connector wires heat up after 1 minute of use? (Assume all energy absorbed by the connector wires is converted to heat and remains in the copper wire.) Remember that E cmAT,…
A DC current I flows in a long solenoidwith n coil-turns per unit length. Thecore is made of iron with permeability µ , and has a cross section area S.Determine the force acting on the coreif it is withdrawn to the position shownin figure.
Q3: A ring has a diameter of 15 cm and a cross – sectional area of 20 cm² .The ring is made up of semicircular section of cast iron and cast steel, with each joint having a reluctance equal to an air-gap of 0.3 mm. Find the ampere-turns required to produce a flux of 16 × 10~4 Wb.The relative permeabilities of cast steel and cost iron are 800 and 166 respectively. Neglecting fringing and leakage effects.
Give the definition of the electromotive force (e.m.f.) E though the the flux linkage ?ϕ and time ?t. Please use "phi" (without the quotes) for flux linkage when typing the answer. For derivatives, please use "d" (again without the quotes).