2. The lap joint in the figure is made using a 30 mm diameter bolt. The outer plates are 5 mm thick, made of 2014- T6 aluminum and the inner plate is 10 mm thick and made of 6061-T6 aluminum. The bolt is made of S355 steel material. Calculate the load P that the lap joint can safely support, taking into account the failure of the plates by shear and tension and failure of the bolt by bearing and shear. Use a factor of safety for ultimate strength of F.S.=1.5 100 mm 20 mm P/2 P/2

2. The lap joint in the figure is made using a 30 mm diameter bolt. The outer plates are 5 mm thick, made of 2014- T6 aluminum and the inner plate is 10 mm thick and made of 6061-T6 aluminum. The bolt is made of S355 steel material. Calculate the load P that the lap joint can safely support, taking into account the failure of the plates by shear and tension and failure of the bolt by bearing and shear. Use a factor of safety for ultimate strength of F.S.=1.5 100 mm 20 mm P/2 P/2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Let's considera rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F Select one: OF 5236 N O F=15708 N Clear mopshoe Finish attempt
Agui - 4550/2 =2276 two plates each with thickness t - 16 mm are bolted together with 6-222 mndia. bolts firming alap Joint Bolt spacing are follows St- $40mm S2 - 80mm, S3=150mm effective bolt hole dia. is 25mm A36 is used. Compute the allowable tensile Strength P t = 16 mm &t 52 747₁ 0 O O 40 60 80 40 +=16mm S-400 $3-100 S2-40 7 @ 4umm P
The AB bond must be made of a steel for which the normal stress limit is 450 MPa. Determine the cross-sectional area for AB for the which the safety factor is 3.50. Suppose the link is adequately reinforced around the pins at A and B. What is the deformationof bar AB when subjected to the load applied to it considering the modulus of elasticity of steel E = 210 Gpa and the length L of thebar equal to 0.75m (All dimensions are in meters)?
The figure gives the cross-section of a grade 25 cast-iron pressure vessel. A total of N bolts are to be used to resist a separating force of 150 kN. (a) Determine kb, km, and C. (b) Find the number of bolts required for a load factor of 2 where the bolts may be reused when the joint is taken apart. (c) With the number of bolts obtained in part (b), determine the realized load factor for overload, the yielding factor of safety, and the load factor for joint separation. Use (SI) units as it applies
A 3-in Aluminum plate and a 2-in cast-iron plate are compressed with one bolt and nut. The bolt is 7/8 in-9 UNC. (1) Determine a suitable length for the bolt, rounded up to the nearest in. (2) Determine the bolt stiffness. (3) Determine the stiffness of the members.
V-links "Im crank arm раper rolling machine forks rod off-loading station air cylinder fork lift truck Determine the critical load on the air-cylinder rod if the crank arm that it rotates is 0.3 m long and in the position with the largest compression of the rod its length equals 0.5 m. The 40-mm-dia rod is solid steelwith a yield strength of 400 MPa. Assume the rod is a fixed-pinned column. Use a theoretical value for the effective length factor. Express your answer to three significant figures and include the appropriate units. HA Per = 1026 kN
Current Attempt in Progress The pin-connected structure consists of two cold-rolled steel (E-31.000 ksil bars (1) and a bronze (E-12.000 ksil bar (2) that are connected at pin D. Each steel bar has a cross-sectional area of 0.125 in 3 A load of P-17 kips is applied to the structure at pin D. Using a-3.3ft and b-5.8 ft. calculate the area required for bar (2) so that each bar carries the same force. Answer: A- for Later W B (2) (1) in 2
An M 14 x 2 hex-head bolt with a nut and a 14R washer under each of bolt head and the nut is used to clamp together two 18-mm steel plates. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the bolt stiffness. The bolt stiffness kb is 592.69 MN/m.
An aluminum ring has an outside diameter of 12.0 mm and an inside diameter of 10 mm. If the ring is short and is made of 2014-T6, compute the 3-13. force required to produce ultimate compressive failure in the ring. Assume that s, is the same in both tension and compression.
Design a cotter joint to support a axial load of122kN kN . Carbon steel material selected which has Tensile stress = 100MPa Compressive stress =150MPa; Shear stress=60MPa
A hollow aluminum cylinder made of 2014-T4 has an outside diameter of 2.50 in. and a wall thickness of 0.085 in. Its length is 14.5 in. What axial com- pressive force would cause the cylinder to shorten by 0.005 in.? What is the resulting stress in the 3-25. aluminum?
Design a knuckle joint subjected to axial tensile forceof 50 kN. Determine the dimensions and failure analysis for the knucklejoint whose rods and pin are made from a selectedmaterial, Steel-Cast (Syt=500MPa) withfactor of safety of 3 .