(2) ihäi An 8V, 400 mA DC motor with a microcontroller. The microcontroller has output pins with 3.3V, 8mA rating. Current gain of the Darlington pair is :100. Then the circuit will LaunchPad +8. Vbus DC motor ER IN914 Gnd PFO ΤIP120 emf HPF4 Rp PAS W 1 ko Not working properly Motor will turned on properly Microcontroller will be damaged Working properly W0000

(2) ihäi An 8V, 400 mA DC motor with a microcontroller. The microcontroller has output pins with 3.3V, 8mA rating. Current gain of the Darlington pair is :100. Then the circuit will LaunchPad +8. Vbus DC motor ER IN914 Gnd PFO ΤIP120 emf HPF4 Rp PAS W 1 ko Not working properly Motor will turned on properly Microcontroller will be damaged Working properly W0000

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100 sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816
The half wave rectifier is supplied with 240V, 50HZ signal. Assume the number of turns in the primary to secondary ratio is 7:2. Calculate the average dc current through the load resistor 4KQ. a. 2.83mA b. 3.667mA c. 7.716mA d. 9.86mA
A 120 Vp is applied to the primary coil of a center-tap transformer of turn ratio (n1 : n2 = 6: 2) . If the secondary coils are connected to a Ge diodes center-tap full wave rectifier, the output DC voltage is about __________. *1- 13.42 V2- 14.15 V3- 15.58 V4-12.54 V5- 16.23 V
A three phase full wave rectifier is shown below along with the peak input phase voltage Vm=169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is Vpc=280.7V and. The RMS transformer secondary current is equal to 81.72A, the output RMS voltage is equal to VRMS=280.93V and the output resistance is equal to 2.8070. The TUF would be equal to: Secondary a平a字a辛 R 太D。太D。太D. Select one: 0.875 Ob. 0.955 O C. 0.551 O d. 0.432 Compared with power transistors, thyristors have the following characteristic
A three phase full wave rectifier is shown below along with peak phase voltage Vm-169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is %3D VDc=280.7V and the output RMS voltage is equal to VRMS=280.93V. The efficiency, FF and RF are respectively equal to: Secondary D D D, R AD. Z D. D, Select one: O a. 99.83%, 100.08%, 4% O b. 99.83%, 55.08%, 4% O C. 99.83%, 100.08%, 16% O d. 87.83%, 100.08%, 4%
What is the ripple factor and what causes it? Discuss and explain how this factor can be used as a metric to improve the quality of the designed AC to DC converting system
A single phase full converter feeds power to RLE load with R= 10 2, L = 10 mH and E = 50 V, the %3D ac source voltage is 230 V, 50 Hz. For continuous conduction, what is the average value of load current for firing angle delay of 60°?
A 3-phase half wave controlled AC to DC converter is supplied from a 250V, supply. Assume the thyristor voltage drop to be 1.6V and the load current to be continuous. Evaluate the mean output voltage when firing angle is varied at 45(degree) , 60(degree) and 90(degree)
Draw the schematic of the Bidirectional Full Wave Control and its load voltage waveform.
By comparing the performance of DC -DC chopper with controlled rectifier circuit which one of the following statement is wrong ? O a. Efficiency is better in chopper circuit b. small filters are required in chopper circuit O c. Regenerative braking process is very slow in chopper circuit O d. Switching frequency is responsible for output ripples in chopper circuit Clear my choice
In the full-wave rectifier circuit, the transformer has a turn ratio of 1:2. The transformer's primary winding is connected across an AC source of 230V (rms), 50 Hz. The load resistor is 50. For this circuit, determine the DC output voltage (3 significant figures)
6. A simple capacitor filter fed by a full-wave rectifier develops 14.5 V dc at 8.5% ripple factor. What is the output ripple voltage (rms)?