17. Which of the following can be used to bond the metal parts at services? A. Ground clamps B. Listed lugs C. Threadless couplings D. Conduit hub fittings 18. Which of the following provides a means for separating and isolating the neutral bus from the equipment grounding terminal bus and the enclosure? A. Grounded neutral conductor B. Neutral disconnect link C. Phased neutral conductor D. Neutral point

17. Which of the following can be used to bond the metal parts at services? A. Ground clamps B. Listed lugs C. Threadless couplings D. Conduit hub fittings 18. Which of the following provides a means for separating and isolating the neutral bus from the equipment grounding terminal bus and the enclosure? A. Grounded neutral conductor B. Neutral disconnect link C. Phased neutral conductor D. Neutral point

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter10: System Protection

Section: Chapter Questions

Problem 10.27P

See similar textbooks

Similar questions

9. Which grounding method is typically required of higher-voltage systems? A. Grounding through inductorsB. Grounding through a low amount of resistanceC. Grounding through a high-impedance device D. Grounding through surge arresters 10. Which term relates to the conductors connected to the output side of a separately derived system? A. Neutral conductorB. Transformer secondary conductorC. System conductor D. Derived phased conductor 11. If there's no service disconnect at a remotely supplied building, then the grounding electrode conductor and the equipment grounding conductor can be bonded together at a A. junction box.B. structural steel location. C. grounding electrode rod. D. water line. 12. In a DC system, the bonding jumper between the negative of the supply and ground is normally made at the source or at the A. first disconnecting means. B. first device on the supply. C. end of the DC line.D. entrance to the building. 13. Which of the following is a common raceway…
Q3. In a % differential scheme, figure shown below, the two CTs have nominal ration of 100:1. The CT errors for a through fault current of 5000 A are as following: CT1 CT2 Ratio error: 10% 10% Phase angle error: 5% -5% Compute following: i) The spill current of the OC relay in the spill path. ii) If the relay is 50% biased, examine whether relay will trip or remain stable CT, CT Ir CB C.B. メx Egu inder Ne
For grounded systems, the _ for the service and the system bonding jumper for separately derived systems provides the critical link between the equipment grounding conductor and the grounded system conductor. A.main bonding jumper B.Service transformer C. Current transformer D. Grounding electrode
Below figure shows a single line diagram of a portion of a radial distribution system. The PS of Relay 3 (R3) is 75% of CT Secondary and time setting multiplier is given 0.1. The CT ratio is given with each relay and fault current of each in bus bar is given in figure. PS for R1 and R2 is set at 100%. Determine the operating time of each relay. Consider 0.25 sec for time coordination time interval. R30.297 R2 = .475 R1 = .654 A B C ID 1000/1 R₁ 10,000 A 800/1 800/1 M R₂ R₁ 8000 A 6000 A 5000 A
1).What factors should be considered when selecting the plug setting of an overcurrent relay. 2) Describe the principle of operation of a directional over-current relay. 3).What are the factors that should be considered when implementing a biased differential protection scheme for a star/delta transformer. Draw a single line diagram to show the connections.
Which of the following cannot be determined with the help of load flow analysis?a) frequency of busbar voltagesb) active and reactive forcesc) phase angle of busbar voltagesd) loss of strengthe) amplitude of busbar voltages
A radial system shown in figure below is fed from a supply of 220 Volt. All impedance values are referred to 220V side (3 phase). When a three phase fault occurs at E, relay D will operate with 0.4 second longer than relay at E. Determine TSM (Time Setting Multiple) at A, B C and D by taking discrimination time (DT) equal to 0.4 second, and TSM at C is already set equal to 0.05. The protection data is as given in figure while IDMT relay characteristic is as in table.
Explain prevention of Arc restriking Theories in circuit breaker.
12. If overcurrent protection is provided in the transformer of a separately derived system, which of the following statements is correct?A. A ground electrode must be present at the transformer and the building's disconnect.B. There's no need for service equipment or a panelboard in the separate building.C. An equipment grounding conductor must be run with the conductors between the transformer and the building's disconnect.D. The neutral should be bonded to the equipment grounding conductor at the service equipment in the separate building.
c.1. Which of the following is one of the three essential functions of an equipment grounding conductor?A. Provide an arc-fault current pathB. Establish groundingC. Establish bondingD. Ensure the system is groundedc.2. What's another name for the three-point method of Earth resistance testing?A. Fall-of-potentialB. Line surgeC. Spatial shieldingD. Leakage current c.3. If the National Electrical Code provides a requirement to ground equipment, it generally implies thatthere will be a direct connection to the Earth of a connection through a/anA. grounding electrode conductor.B. equipment grounding conductor.C. equipotential bonding conductor.D. bonding conductor.
1-Draw the structure of single bus bar system. 2-Write the methods of Neutral Grounding.
In the medium voltage air line network given in the figure,a) Draw the protection scheme of one of the transformers connected in parallel together with the protection controls as three poles.b) Construct a protection system with overcurrent time relays with a minimum opening time of 0.5 s and time steps of 0.5 s.