100 atm 1 atm 0.118 atm 114 °C 184 °C 535 °C Temperature (not to scale) a.) Use the above generic phase diagram, clearly identify where you would find the following: Gas, Liquid, Solid, Triple Point, Draw arrows and label to indicate the six transitions (melting, freezing, sublimation, deposition, vaporization and condensation) b.) Based on the above phase diagram, what phase would you be in at a pressure of 50 atm and 300°C? c.) Based on the above phase diagram at what temperature in °C would vaporization occur under normal conditions? d.) If the pressure was 0.050 atm and 425°C, what phase would you be in? e.) If the pressure was 0.118 atm and temperature was 114°C, what phase(s) would you be in? f.) At approximately what temperature would the normal freezing point be in °C? g.) If the pressure was 0.105 atm and starting at a temperature of 32°C to 450°C what phase changes would occur (put in increasing temperature order). Pressure (not to scale)

100 atm 1 atm 0.118 atm 114 °C 184 °C 535 °C Temperature (not to scale) a.) Use the above generic phase diagram, clearly identify where you would find the following: Gas, Liquid, Solid, Triple Point, Draw arrows and label to indicate the six transitions (melting, freezing, sublimation, deposition, vaporization and condensation) b.) Based on the above phase diagram, what phase would you be in at a pressure of 50 atm and 300°C? c.) Based on the above phase diagram at what temperature in °C would vaporization occur under normal conditions? d.) If the pressure was 0.050 atm and 425°C, what phase would you be in? e.) If the pressure was 0.118 atm and temperature was 114°C, what phase(s) would you be in? f.) At approximately what temperature would the normal freezing point be in °C? g.) If the pressure was 0.105 atm and starting at a temperature of 32°C to 450°C what phase changes would occur (put in increasing temperature order). Pressure (not to scale)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Temperature, °C Temperature, F Temperature, °C Temperature, (b) The Low carbon steel (1% C) is required to be hardened by heat treatment. Related phase diagram and TTT diagram are given below in Figure Q3(b). Illustrate the phases obtained and procedure of the heat treatment process 1800 Liquid (L) 3200 Austenite, y 800- A, = 723°C (1333 F) 1400 2800 1400 700아 P, 1200 Start Pearlite, P 2400 600- Y+ L L+ Fe,C Finish 1000 u Y+ a 1130°C (2066°F) 2000 500- a+ Fe,C 1000 a +Y -800 400- Y 1600 A B, B, Bainite, B Y+ FegC Solid 600 723°C (1333°F) 300F Ms 1200 600 400 200 800 a + Fezc Solid Y+M 100- M 200 200 - 400 Martensite, M 102 Time, s 1.0 10 10 10 6 Fe % Carbon (C) TTT diagram Fe-Fe carbide phase diagram Figure Q3(b)
For the given Ti-Cu phase diagram, specify all temperature-composition points at which eutectics, eutectoids, peritectic, and congruent phase transformations occur. Also, for each, write the reaction upon cooling. Temperature (°C) 1700 1500 1300 1100 900 700 500 0 (Ti) 1 B a 20 Ti₂Cu 40 Composition (wt% Cu) L TiCu TigCu4 60
The figure below shows Pb-Sn phase diagram. What is the composition of Pb and Sn at point 1? 1200 1000 Liquid a +L 779 C (Tg) B+L 6 800 8.0 71.9 G 91.2 600 400 200 20 40 60 80 100 (Pb) Composition (wt% Sni (Sn) Callister Jr., W.D., 2007 O a. 80 wt % Sn and 20 wt % Pb O b. 10 wt % Sn and 90 wt % Pb O c. 90 wt % Sn and 10 wt % Pb O d. 20 wt % Sn and 80 wt % Pb Temperature ("C)
b) Figure 1 shows a Cu-Ag phase diagram. Calculate the phase analysis for 50% Ag-50% Cu at 800 °C. Temperature (°C) 1200 1000 800 600 400 200 ( C (Cu) B 8.0 (C₂g) -Solidus Solvus 20 20 a + L Composition (at% Ag) 40 -Liquidus 779°C (TE) a + B 40 Liquid 60 Composition (wt% Ag) 60 71.9 (CE) 80 80 B+L 91.2 (CBg) G to 100 2200 2000 1800 F 1600 1400 1200 1000 800 600 400 100 Temperature (°F)
Choose the corect answer -A vertical line in the phase diagram represents a.an intermetallic compound b.a eutectic phase c.a eutectoid phase Match each statement with a letter -In the peritectoid reaction -In the Peritectic reaction: -In the Monotectic reaction: -In the Eutectoid reaction: -In the Eutectic reaction: a. a liquid phase transforms into two solids when it is cooled down b. a solid phase transforms into two different solids when it is cooled down c. a liquid phase transforms into a new liquid phase and a solid phase d. Two solid phases transform into a new single solid phase e. A solid phase and a liquid phase transforms into a solid phase
A substance exists in two solid modifications alpha and beta and also as liquid and vapour at a pressure of 1 atm alpha melts at a lower temperature to form liquid. Also alpha is denser than the liquid but beta is less dense than the liquid assuming that no meta stable equilibria are observed sketch p-t phase diagram show the significance of each point,line and region also show all triple points.
1. Visualize a substance with the following points on the phase diagram: a triplepoint at 0.05 atm and 150 K; a normal melting point at 175 K; a normal boiling pointat 350 K; and a critical point at 2.0 atm and 450 K. The solid liquid line is “normal”(meaning positive sloping). For this, complete the following:a. Roughly sketch the phase diagram, using units of atmosphere and Kelvin. Labelthe area 1, 2, and 3, and points T and C on the diagram.b. Describe what one would see at pressures and temperatures above 2.0 atmand 450 K.c. Describe the phase changes from 50 K to 250 K at 1.5 atm.d. What exists in a system that is at 1 atm and 350 K?e. What exists in a system that is at 1 atm and 175 K?2. Based from the phase diagrams of water and carbon dioxide, answer thefollowing questions and justify your answers: 1. You have ice at 263 K (-10.0 oC)and 1.0 atm. What could you do to make the ice sublime? 2. A sample of dry ice(solid CO2) is cooled to 173 K (-100.0 oC), and is set on a table at…
For two hypotetical materials which have limitless solubility for both in the “liquid” and “solid” states in each other, the following data are listed. Melting Temperatures of material A and B are Tm,A and Tm,B respectively, Liquidus and Solidus curves are circular arcs. a- Draw the related “Phase Diagram” of Material A and Material B showing the data given and calculated. b- Calculate/Determine the compositions of phases at T2 , explain the procedure. c- Calculate/Determine the “percentages” of “phases” of Alloy,2 at T2 , explain the procedure. Given: -Tm,A, Celcius =300 -Tm,B, Celcius =800 -T1, Celcius =600 -B percentage of Liquid phase at T1 =25 -B percentage of Solid phase at T1 =70 -B percentage of Alloy 2. =50 -T2, Celcius =650 -B percentage of Liquid phase of Alloy 2 at T2 = to be calculated -B percentage of Solid phase of Alloy 2 at T2 = to be calculated
2. a) How many kilograms of nickel must be added to 1.75 kg of copper to yield a liquidus temperature of 1300 °C? b) How many kilograms of nickel must be added to 5.43 kg of copper to yield a solidus temperature of 1200 °C? c) The solidus and liquidus temperatures for the copper-gold system are given here. Construct the phase diagram for this system and label each region. Composition (wt.% Au) Solidus Temperature (C) Liquidus Temperature (C) 1085 1085 1019 972 20 1042 996 946 40 60 934 80 911 911 90 928 942 95 974 984 100 1064 1064
Given a blank phase diagram, label the solid, liquid, and gas phases for a pure substance. Give the approximate temp. and pressure of the triple point, and determine what the substance's phase would be at a given temperature and pressure. Can you provide an example?
Consider Cu - Ag Phase diagram below: 1200 A -Liquidus 1000 Liquid -Solidus 779°C (TE) 800 Temperature (°C) 600 400 a C 200 0 B 8.0 (Cag) Solvus a +L a + ß E 71.9 (CE) B+L 91.2 (CBE) B H 1 1 1 1 1 { ( L 20 40 60 80 100 (Cu) Composition (wt% Ag) (Ag) Consider 71.9% Ag-28.1% Cu, which is cooled below 779°C. What is the composition of the phases present just below 779°C and give the amount of beta phase present
Phase Diagrams: You are given the lead tin (Pb-Sn) phase diagram. Below the eutectic isotherm is identified as the two phase region a + B. a) At 30wt % Sn, in the circles below draw the microscopic observations evolving at 3000C, 2250C, and 1000C for this hypoeutectic alloy. b) At a temperature just above the isotherm at 1830C, for the 30 wt% Sn Alloy, calculate the fractions of each phase present at equilibrium and the corresponding composition of each phase.