1.4 Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN? Bronze Alumimum A=600 mm Steel A=400 mm² 2P A= 300 mm 3P 4P P

1.4 Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN? Bronze Alumimum A=600 mm Steel A=400 mm² 2P A= 300 mm 3P 4P P

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.13P: Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses...

See similar textbooks

Related questions

Q: Q1/A steel bar ABCD (4m) long is subjected to forces as shown in Figure. Find the stresses in each…

Q: 4. The lap joint is connected by three 20-mm-diameter rivets. Assuming that the axial load P=50 kN…

A: a.Shear stress in rivet:ss=PAs=50×1000π4×20×20×3=53 MPa

Q: Question 4: Two wrenches are used to tighten the pipe. If the pipe is made from a material having an…

Q: Two solid cylindrical rods support a load of P = 27 kN as shown. Rod (1) has a diameter of 17 mm,…

Q: 9. A rod has three segments as shown in the figure. The position of applied loads and diameter of…

Q: 1. Three long parallel wires equal in length are supporting a rigid bar connected at their bottoms…

A: It is the conceptual numerical of mechanics of solid portion and used concept is axial deformation…

Q: In a pure shear condition, the maximum value of shear stress is observed to be 20 MPa for a element…

A: Let us start by calculating the diagonal AB.The length of AB is given as:AB = 0.1m2+0.1m2 =0.414 m

Q: Homework :-in the figure shown. Find the total deformation and the stress in each section if E is…

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A: GIVEN DATA A COMPOSITE ROD AXIALLY LOADED GIVEN WE HAVE TO FIND STRESS IN EACH ROD Load P=3800lb…

Q: Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm…

Q: An aluminium rod is rigidly attached between a steel rod and a bronze rod as shown in Figure 3.…

Q: A clevis-type pipe hanger supports an 8-in.-diameter pipe, as shown in Figure. The hanger rod has a…

A: Given data: W=2000 lb Need to determine the normal stress in the hanger rod, shear stress in the…

Q: Compute the max load (P ) if the stress in steel 120 Mpa and in bronze 70 Мра steel bronzel A=…

A: σsteel=120Mpaσbronze=70Mpato find:- Maximum load(P)

Q: A three segments of steel rods, is shown in the following Figure. Each rod has a diameter as shown…

Q: Two are connected by a knuckle jont, as shown in Fig by a pin of 40 mm in diameter. If a pull of 120…

Q: Question # 1 Fig 2 shows an unstressed aluminum plate 2/4 inches thick. A circle of 9.5 inches…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: Determine the largest weight W that can be supported by the wires shown in figure. The stress in…

Q: b) An aluminium rod is attached between a steel rod and a bronze rod as shown in Figure-3. The axial…

A: Given data: The area of the bronze section is, A1=250 mm2. The area of the aluminum section is,…

Q: Homework one (Simple Stress) QI Two solid cylindrical rods AB and BC are welded together at B and…

Q: 4- Determine the stress when Temperature change from 20 C° to 60 C° . steel aluminum 20 kN 200 mm…

Q: 1. Three vertical rods AB, CD, and EF supports s load of 36 kN. Each of the rods AB and CD has a 200…

A: When an external force is applied to any body the body gets deformed. This deformation is resisted…

Q: Q2/ A steel bar shown in figure consists of two segments having diameter of AB= 28 mm and BD= 40 mm.…

Q: Q2) In Fig.(2), the shaft is subjected to reversed loads, F = F 2700 N and P = F 1350 N, where these…

Q: A steel rod is acted upon by the loading shown below. 50 mm² is the area of the circular rod. The…

Q: 3- A Compound bar composed of three bar as shown .Determine the stress if the temperature change…

A: Calculated stress in brass and aluminum block when it compounded.

Q: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure.…

A: Consider the Free Body Diagram: Force acting on Bronze rod:FCD=2PStress in Bronze…

Q: A circular steel bar is subjected to various forces as shown in Fig. determine: 1) P 2) The total…

A: Given: A circular steel bar is shown below:

Q: A1 A uniform bar of length L and cross sectional area A is held vertically at the upper end and…

A: When a uniform bar is hanged hanged vertically, the weight of bar varies from zero to W. At tip, it…

Q: The assembly in Figure below consists of a light rigid bar AB, pinned at O, that is attached to the…

A: Given:AB=0.75mOB=1.5m∆=5mmFor steelAst=250mm2E=200 GPaFor aluminiumL=BC=2mAal=300mm2E=70 GPaTo find…

Q: A rod is composed of three segments as shown and carries the axial loads P1=120 kN and P2=50 kN as…

Q: Two solid cylindrical rods support a load of P = 32 kN as shown. Rod (1) has a diameter of 14 mm,…

Q: piece of wood, 84 mm by 180 mm, is used as a compression block. The grain of the wood makes a 21.2º…

Q: The cross-sectional area shown is subjected to V = 600 kN and M =1000 kN-m. What is the flexural…

Q: The lap joint is connected by three 10-mm-diameter rivets. Assuming that the axial load P = 100 kN…

Q: A metal rod having two different diameters is loaded by an axial force P. Segments (1) and (2) are…

Q: 1. Consider a deformable homogenous siender rod of constant area along its length. It is axially…

A: According to st. Venant's theory, maximum normal strain in actual case crosses maximum normal strain…

Q: Q1: A steel pipe column with outside diameter0.5 in and its wall thickness 0.25 in. supports a load…

A: The bearing stress is calculated by dividing the force that presses a structure by its area. It can…

Q: b) An aluminium rod is attached between a steel rod and a bronze rod as shown in Figure- 3. The…

A: Given data: The area of steel bar is As=550 mm2 The area of Aluminium bar is Aal=400 mm2 The area of…

Q: A clevis-type pipe hanger supports an 8-in.-diameter pipe, as shown in Figure. The hanger rod has a…

A: Given data: W=2000 lb Need to determine the normal stress in the hanger rod, the shear stress in the…

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

Q: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure. Axial…

Q: The steel tie-bar shown in the figure has been designed to carry a tension force of 55 kN when…

Q: The rigid bar ACE is supported by two steel rods AB and CD (Esteet = 200 GPa) with the cross…

Q: Determine the largest weight of the picture frame that can be by the two ropes Tas shown in the…

Q: An aluminum rod is rigidly attached between bronze rod and steel rod as shown. Axial loads are…

A: Given: The maximum value of stress in steel is σs=120 Mpa. The maximum value of stress in aluminum…

Q: 1. Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square…

Q: Fig. 1.42 shows a system of three springs in series subjected to two axial loads. The stiffnesses of…

Q: 1.16 The 1000-kg uniform bar AB is suspended from two cables AC and BD, each with cross-sectional…

A: Determine the tension in the rod BD.

Q: Determine the largest weight W (in Ib) that can be supported safely by the structure shown in the…

Q: The support consists of solid brass post surrounded by a steel tube. Before the load is applied, the…

A: The axial force is the rod's compression or tension force. The maximum load, places the rod in an…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

1.4 Axial loads are applied to the compound rod that is composed of an aluminum
segment rigidly connected between steel and bronze segments. What is the stress in
cach material given that P = 10 kN?
Bronze
Aluminmım
Steel
A=400 mm2
2P
A=600 mm
A= 300 mm
3P
4P
P
m 5m-
-4m-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
Consider the copper lubes joined in the strength of the copper is err = 200 MPa, figure using a "sweated" joint. Use the properties and what is the maximum load P]iwathat can be dimensions given. applied to the joint if the desired factor of safety in shear is FS_ - 2 and in tension is (a) Find the total elongation of segment 2-3-4 (
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
The strength-to-weight ratio of a structural material is defined as its load-carrying capacity divided by its weight. For materials in tension, use a characteristic tensile stress obtained from a stress-strain curve as a measure of strength. For instance, either the yield stress or the ultimate stress could be used, depending upon the particular application. Thus, the strength-to-weight ratio RS/Wfor a material in tension is defined as Rs/w= in which a is the characteristic stress and 7 is the weight density. Note that the ratio has units of length. Using the ultimate stress Uas the strength parameter, calculate the strength-to-weight ratio (in units of meters) for each of the following materials: aluminum alloy 606I-T6, Douglas fir (in bending}, nylon. structural steel ASTM-A57.2, and a titanium alloy. Obtain the material properties from Tables [-1 and 1-3 of Appendix I. When a range of values is given in a table, use the average value.
1. A solid square rod is cantilevered at one end. The rod is 0.8 m long and supports a completely reversing transverse load at the other end of 50 kN. The material is AISI 1060 hot-rolled steel (?? =370 MPa,?? =680 MPa ). Use a design factor of 2 and determine the dimensions of the square cross section for the following cases. Neglect any stress concentration. a. The rod must support this load for 100 cycles. b. The rod must support this load for 104 cycles. c. The rod must have infinite life.
Let's considera rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F Select one: OF 5236 N O F=15708 N Clear mopshoe Finish attempt
3. A steel bolt and nut are tightened around an aluminum sleeve. Find the internal forces as the nut is rotated 1 turn (1 turn = 1.5 mm) given the cross sectional areas and the moduli of elasticity for the steel and the aluminum. AST = 150 mm? EST = 200 GPa EAL = 70 GPa AAL = 100 mm? L=150 mm AST Final 1.5 mm Position Al
Clear my choice Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F. Select one: O F= 5236 N OF=15708N O F= 13090 N OF=10472 N OF=4189 N O F=6283 N Clear my choice Finish attempt NEXT ACTIVITY MENG360 Test -Spring 2020-2021 Jup to
A hollow aluminum cylinder made of 2014-T4 has an outside diameter of 2.50 in. and a wall thickness of 0.085 in. Its length is 14.5 in. What axial com- pressive force would cause the cylinder to shorten by 0.005 in.? What is the resulting stress in the 3-25. aluminum?