1. For the state of plane stress with x-y axes as shown, do the following: 12 MPa 1.1 draw the Mohr's circle using the sign convention discussed in + 7 MPa class 1.2 determine the principal normal stresses and the angle from the x-axis to o, 4 MPа 1.3 draw the state of stress on an element rotated 30° clockwise X from the x-axis

1. For the state of plane stress with x-y axes as shown, do the following: 12 MPa 1.1 draw the Mohr's circle using the sign convention discussed in + 7 MPa class 1.2 determine the principal normal stresses and the angle from the x-axis to o, 4 MPа 1.3 draw the state of stress on an element rotated 30° clockwise X from the x-axis

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.1P: The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the...

See similar textbooks

Similar questions

-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses with a magnitude of 42 MPa in the horizontal direction and tensile stresses with a magnitude of 9.5 MPa in the vertical direction (sec figure part b). Also, shear stresses with a magnitude of 15.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40g from the horizontal. Show these stresses on a sketch of an element oriented at this angle.
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the \y axes, that is, determine crv, tr(_, and t, Show the results on a sketch of an clement oriented at B .
Consider the plane stress element shown in representing the state of stress at a material point. If the magnitudes of the stresses are such that ox 210 Pa, oy = 110 Pa, and = - Txy = 70 Pa, calculate the magnitudes of principal stresses oj and 02, and the maximum shear stress, Tmax, generated at %3D this material point. (a) Record here the the positive of the two principle stresses. (b) Record here the the negative of the two principle stresses. (c) Record here the the maximum shear stress. Tyz Oy
the state of stress at a point can be described by óx=36 MPa and Txy= 17MPa a second coordinate system is rotated by theta35 degrees What is the normal stress in the direction of the x' axis what is the shear stress in the y'-direction for the faces with a normal in the x'-direction what is the normal stress in the direction of the y'-axis
Q1. For the given cube below, complete the following: 1.find the center, radius (R), principal normal stresses (σ and σ3), max shear stress (Tmax) and draw the Mohr's Circle. 2. Find the stresses on a plane that is rotated 60° clockwise from the horizontal plane. 6PSE IPSF 10pst 60⁰ TOPST IPSF 6PSF
Consider the 2-D state of stress shown below. Using the provided scales graph the Mohr's Circle for the 2-D state of stress with “full" details II-Obtain the Principal Stresses, the Maximum Shear Stress, and complete the table below III- Draw the Planes of Principal and Maximum Shear Stresses in the space provided below Provide "full" details and Use 3 Sig. Fig. in this problem Oy = 15 Ksi Tcw > S y Ox =10 Ksi Тух 5 Ksi 10 5 -20 -15 -10 5 10 15 20 5 10 Tccw > S' O Avg. TMax. 01 02 Op1
(a) Construct Mohr's circle for an element in a uniaxial state of stress (b) Use this Mohr's circle to derive the equation for the normal stress On and shear stress En on the n-face. The equations should depend on Ox and θ (c) Use the Mohr's circle to determine the planes on which the maximum shear stress acts. Sketch a properly oriented maximum-shear-stress element and indicate the normal and shear stresses acting on its faces. Ơn nt o, Note: for (b), the angle θ is between 0 and 90° and is positive
Problem 2: For the plane stress state listed below, draw a Mohr's circle diagram properly labeled. Keep in mind that the principal stress is that stress state where the shear stress is zero. That means it is the stress state along the normal stress line in Mohr's space. So, use your Mohr's circle to find the principal normal and shear stresses, and determine the angle from the x axis to o1. 0x = 20 kpsi, oy =-10 kpsi, Txy = 8 kpsi cw