1. For the given soll element, determine: C a. Determine the maximum and minimum principal stresses. b. Describe the location of the maximum principal stress from side BC. c. Describe the location of the maximum principal stress from side BD. d. Determine the maximum shear stress. e. Determine the normal and shear stresses at plane AB.

1. For the given soll element, determine: C a. Determine the maximum and minimum principal stresses. b. Describe the location of the maximum principal stress from side BC. c. Describe the location of the maximum principal stress from side BD. d. Determine the maximum shear stress. e. Determine the normal and shear stresses at plane AB.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.4P

See similar textbooks

Similar questions

- [Mohr's Circle]. . For the stressed soil element shown below, determine a. Major Principal Stress in psi. b. Minor Principal Stress in psi. c. Normal Stress at Failure Plane AE in psi. d. Shear Stress at Failure Plane AE in psi. 150 psi 60 psi 90 psi 60 psi 45 A B.
The vertical compressive stress at a point in a soil is 100 kN/m2 while the horizontal compressive stress at the same point is 62 kN/m². Both stresses are principal stress. (a) Draw the Mohr circle that describes the 2D stress state at the point (hand sketch is ok). (b) Find the maximum shear stress that acts at the point. (c) Determine the angle of the plane on which the maximum shear stress acts and obtain the normal stress on that plane (Use the pole method - the method is simplified since the stresses given in the problem are principal stresses). (d) Confirm the maximum shear stress and the normal stress from (c) using the stress transformation equations (consider sign conventions!).
The vertical compressive stress at a point in a soil is 100 kN/m2 while the horizontal compressive stress at the same point is 57 kN/m2. Both stresses are principle stress. (a) Draw the Mohr circle that describes the 2D stress state at the point. (b) Find the maximum shear stress that acts at the point. (c) Determine the angle of the plane on which the maximum shear stress acts and obtain the normal stress on that plane (Use the pole method). (d) Confirm the maximum shear stress and the normal stress from (c) using the stress transformation equations (consider sign conventions!).
determine the maximum shear stress. sketch thesection stress distribution
A soil profile consists of a clay layer underlain by a sand layers as shown. A tube is inserted into the bottom sand layer and the water level rises to 1.2m above the ground surface. Determine the effective stress at pt. A Determine the effective stress at pt. B. Determine the effective stress at pt. C Please answer this asap. For upvote. Thank you very much
For soil elements shown in the figure, determine the maximum and minimum principal stresses. Also determine the normal and shear stresses on plane AB.
A strip load of q = 900 lb/ft2 is applied over %3D a width, B = 36 ft. Given: x = 21 ft the %3D increase in vertical stress at point A located z= 15 ft below the surface is (Ib/ft2) B q = load per unit area Δα 162 O 152 142 O
At a point P, the rectangular stress components are: x = 1, y = -2,0 = 4, y = 2, T = -3 and T = 1 yy all in units of kPa. Find principal stresses and check for invariance.
A thin layer of clay subjected to drying develops internal shrinkage stresses. The state of effective stress at a point in this layer is shown in the figure (a) below. Plane stress condition can be assumed for this problem. Elastic modulus, E of clay is 15 MPa and Poisson's ratio, v is 0.35. Hooke's law is valid during drying, meaning that (o,- vo,) *3 where s,is the strain in x direction. 12 kPa 19 kPa Tx1y1 46 kPa 15° (a) Before curling (b) After curling
A) Show the following on Mohr's stress circle: 1-The value of direct stress in the plane of the maximum Shear stress. 2-The angle of the maximum shear stress. 3-The value of the shear stress on the principal plane. B) The direct stresses in two mutually perpendicular directions are 50 MN/m² (compressive) and 200 MN/m² (tensile) accompanied by shear stresses of intensity 100 MN/m² clockwise on effect on the plane carrying 200 MN/m² stress. Using Mohr's Stress Circle, find the principal stresses, maximum shear stress, and their planes, the normal and tangential stresses on plane inclined 30 clockwise to the planes of the 50 MN/m² direct stresses. What is the shear stress which acting alone that produce the same maximum principal stress.
3. (a) A prismatic bar is subjected to an axial compressive stress of 85N/mm. Determine the i. Stresses acting on the plane which is at an angle e= 40° with reference to the x-axis. ii. Magnitudes of maximum, and minimum normal stresses induced and the position of their planes Us" ii. Magnitude of normal Stress on the plane of maximum shear stress
4. The rigid slab is supported by two identical copper rods as shown. The copper rod has an area of 500 mm? with a = 16.8 µm/ ( m°C ) and E = 120 GPa. There is a gap of 0.18 mm between the slab and the aluminum rod. The aluminum rod has an area of 400 mm? with a = 23.1 µm/ ( m°C ) and E = 70 GPa. Compute the stress developed in each rod when the temperature is raised to 85°C. Assume that the weight of the slab is negligible. Δ Copper Aluminum Jədder 750 mm -