1. A steel pipe of length 4 ft, outside diameter of 6.0 in., and inside diameter of 4.5 in., is compressed by an axial force of 140 kips. The material has a modulus of elasticity of 30,000 ksi and Poisson’s ratio of 0.30. Determine the following quantities for the pipe: a. The shortening. b. The lateral strain. c. The percentage increase in the outer and the increase in the inner diameter. d. The percentage increase in the wall thickness.

1. A steel pipe of length 4 ft, outside diameter of 6.0 in., and inside diameter of 4.5 in., is compressed by an axial force of 140 kips. The material has a modulus of elasticity of 30,000 ksi and Poisson’s ratio of 0.30. Determine the following quantities for the pipe: a. The shortening. b. The lateral strain. c. The percentage increase in the outer and the increase in the inner diameter. d. The percentage increase in the wall thickness.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.6P: A rubber ball (sec figure) is inflated to a pressure of 65 kPa. At that pressure, the diameter of...

See similar textbooks

Similar questions

A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
A rubber ball (sec figure) is inflated to a pressure of 65 kPa. At that pressure, the diameter of the ball is 240 mm and the wall thickness is 1.25 mm. The rubber has a modulus of elasticity E = 3,7 MPa and Poisson's ratio v = 0.48. (a) Determine the maximum stress and strain in the ball, (b) If the strain must be limited to 0.425, Find the minimum required wall thickness of the ball.
A thin steel cylinder 1.3 m long is subjected to internal pressure, the change in volume owing to the pressure is 17.5 x 10 m³ of the original volume 65.5 x 103 m³. De termine the internal diameter, hoop, and longitudinal stresses. For the cylinder material E = 210 GIN/m², v = 0.3. de 253 What will be the bulk modulus K, if the internal pressure is 14 bar and the extra fluid is 6 * 10 m³ at the same diameter, thickness, and original volume of part (a).
(5) A gas engine valve spring is loaded to 35kgf when the valve is closed & 52kgf hen the valve is open. The valve lift is 8mm. The outside diameter is to be from 38mm~45mm, & the permissible stress is 413N/mm2 . Determine: (a) the wire & outside diameter; (b) the number of effective coils; (c) the free length when it is squared & ground.
3. An axial pull of 35000 N is acting on a bar consisting of three lengths as shown below. If the Young's Modulus is 2.1 x 105 N/mm2. Determine (i) Stresses in each section, and; (ii) Total extension of the bar. Section 3 Section 2 Section 1 35000 N 35000 N 2 cm DIA 3 cm DIA 5 cm DIA k-20 cm- 25 cm -22 cm-
(1) A steel cylinder (Øyp = 260 MPa) of inner radius a and outer radius 3a is subjected to an internal fluid pressure pi (Note: ratio of wall thickness (t) to inner radius indicates that this is a thick-walled cylinder). (a) Determine (i) the maximum radial stress (ơmax); (ii) the maximum tangential stress (o0max). (b) Determine the limiting values of p, using: (i) the maximum distortion energy theory of failure; and (ii) the maximum shear stress theory of failure. (Hint: Maximum radial and tangential stresses occur at the same radial distance, see slide 8 of Lecture 9 notes); use these maximum stresses as your principal stresses). (c) A steel gun barrel of inner radius 0.6 m is subjected to an internal explosive pressure of 80 MPa. The tensile and compressive elastic strengths of the material are 320 MPa. Assuming a factor of safety of 2, design the wall thickness of the gun barrel.
Find the value of strain stress 30 MPa Modulus of elasticity=65 MPa
An element of bone in plane strain where the state of strain are = 12 x 10-4). Find (a) the stresses at (Ex = 8 x 10-4, €y = 5 x 10-4, Yxy orientation a counterclockwise angle (40 deg.) from the x-axis, b) the strain energy and (c) the failure stress by Von Misses criteria. Known Modulus of elasticity = 2 x 10° N/m² and Poisson's ratio = 0.3
The inner diameter of a cylindrical pressure vessel is 400 mm. When subject to pressure, the hoop stress in the cylinder wall is 40 MPa. For the material of construction E = 200 GPa and Poisson's ratio = 0.3. The %3D increase in inner diameter is, O a. 0.016 mm b. 0.08 mm O c. 0.068 mm O d. 0.04 mm
Question 3 - Strain Energy A brass tube with an outside diameter of 20 mm and 4 mm wall thickness is 80 mm long.It is joined to the end of a solid brass rod with a diameter of 20 mm and 120 mm long toform a compound assembly. This assembly is subjected to tension due to a mass of 150kg moving at a speed of 0.4 m/s.3.1. Determine the stresses induced in the rod and the tube respectively.3.2. Determine the change in length of each part, as well as the total change in length ofthe assembly.3.3 Determine the equivalent impact load (in kg) required to have the same effect(produce the same amount of energy) if falls freely from a height of 10 cm onto acollar attached to the bottom of the assembly if the assembly is vertically attachedat its top.3.4 How much strain energy is absorbed by each section of the assembly?(For brass: E = 100 GPa and α = 18×10-6/ 0C)
A steel pipe of length L= 5 ft, outside diameter d₂= 9.3 in., and inside diameter d₁= 5.1 in. is compressed by an axial force P= 577 kips. The material has Poisson's ratio v=0.30. Determine the increase in inner diameter. A
A composite square member of varying sizes is subjected to axial forces along its centerline, as shown. The members' cross-sectional dimensions, from smaller to larger, are 50 mm ´ 50 mm, 75 mm ´ 75 mm, and 100 mm ´ 100 mm, respectively. (a) What are the normal stresses (in MPa) induced in the bar material at Section A-A, Section B-B, Section C-C? (b) What are the changes in the axial (4.28 ft), width (100mm), and thickness (100 mm) direction (in mm), at Section C-C? Assume n = 0.25 and E = 200,000 MPa., 1 ft = 0.3048 m