(1) Simplify the Boolean expression: ((B + C) + ĀD)(Ā+B) (C + D) (2) Draw the logic diagram corresponding to the following Boolean expression without simplifying it: A + CD + (A + D)(C + D) (3) Draw a CMOS circuit (containing both pull-up and pull-down networks) which implements the following logic expression: x, + xz X3

(1) Simplify the Boolean expression: ((B + C) + ĀD)(Ā+B) (C + D) (2) Draw the logic diagram corresponding to the following Boolean expression without simplifying it: A + CD + (A + D)(C + D) (3) Draw a CMOS circuit (containing both pull-up and pull-down networks) which implements the following logic expression: x, + xz X3

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Consider the design of two logic circuits that both have four inputs: A, B, C and D; and one output: X. Each circuit is implemented using 4-input AND gates (with negated inputs) and an OR gate to generate the output. For circuit 1, X is defined to be 1 if and only if the binary representation of A, B, C and D is even. Note A is the most significant bit, then B, then C, and Dis the least significant. For circuit 2, X is defined to be 1 if and only if the total number of 1's among A, B, C and D is even. Which of the following 4-input gates would be used in the implementation of both circuits?
Which of the following is correct regarding the comparison between TTL and CMOS? >CMOS design is less complicated as compared to TTL. >CMOS circuits consume more power compared to TTL circuits at rest. >CMOS allows in a single chip a much higher density of logic functions compared to TTL. >CMOS chips are a lot more susceptible to static discharge compared to TTL chips.
A design engineer has limited resources in terms of logic modules such as AND gate, OR gate and inverter module to implement the function. Simpify the Boolean function F-AB + (ACY + AB'C (AB + C) using theorems and corresponding postulates and mention in each step also.
subject name is "DIGITAL ELECTRONICS" 1: A) What will be the hexadecimal equivalent of the octal number 375525.3276? B) The smallest and largest numbers that can be represented in 13-bit 2's compliment. c) consider a 4-input XOR gate with inputs A, B, C and D. What will happen if the input A is permanently connected to 0. Justify your statement also.
A-Consider a digital counter that counts 0 to 7 when the reset button is 0 and go back to 0 when the reset button is 1. draw the state diagram and state table for the digital control circuit of such a digital counter? B-For the resulted design in A how many configurable logic block (CLB) you would need to implement your design in the FPGA if the CLB structure is as follows: Look-Up Table MUX SET (LUT) CLR
Draw a circuit to realize each of the following expressions using AND gates, OR gates, and inverters: a. F=A+ B ¯ C, b. F=A B ¯ C+AB C ¯ + A ¯ BC, c. F = ( A ¯ + B ¯ +C)(A+B+ C ¯ ) (A+ B ¯ +C)
- The proportional distribution of A, B, C, D signals is given in the table as a percentage. It “logic 1” when the signals are accepted as active, “logic 0” when they are accepted as passive. takes. - When the proportional sum of active signals is over 50%, its output is "logic1", When we accept "logic 0" when it is below 50%, the output in the table Find the values. - Create an X function based on the logic values you find. Simplify the created X function. - Design the simplified function with NAND and NOR gates. - Set up the circuits you designed with NAND and NOR gates and observe the outputs. Show the output values by drawing a table, applying all possibilities to the input values.
- The proportional distribution of A, B, C, D signals is given in the table as a percentage. It “logic 1” when the signals are accepted as active, “logic 0” when they are accepted as passive. takes. - When the proportional sum of active signals is over 50%, its output is "logic1", When we accept "logic 0" when it is below 50%, the output in the table Find the values. - Create an X function based on the logic values you find. Simplify the created X function. - Design the simplified function with NAND and NOR gates.
Draw the equivalent logic circuit diagram of the following expressions : a. XY = F b. X + Y = F XÝZ = F c. d. XY + XZ = F e. XYZ + XÝZ = F
The diagram here shows the pull-down network for a logical gate. What is the logical function that would be implemented by the full CMOS circuit? A- B C D M4 OA. Y = (A+B.C). D O B.Y= (A + B).D+C OC. Y = (A + B). (C + D) OD. Y = A·B+C · D OE.Y=A+B.D+C M3 M1 M2
- Using a 8 X 1 PROM, implement the logic function whose truth table is given : B. C Output (F) 0. 1. 1. 0. 1. 0. 1 0. 1. 1. 67
A combinational circuit has three inputs x, y, and z and three outputs F1, F2, and F3. The simplified Boolean functions for the circuit are: F1 = xz + x’y’z’ F2 = x’y + xy’z F3 = xy + x’y’z Use a 74138 decoder IC and external NAND gates. Provide a schematic logic diagram. Even a photo of it will surely help me in my review. Thank you so much!!