The purpose of this experiment was to perform a nucleophilic substitution reaction to construct a biologically active compound from two simple parts and then to recrystallize the product collected, which is a purification technique that purifies solids based on differences in solubility. In order to accomplish this, other techniques such as heating at reflux, and suction filtration were used. Heating at reflux is a technique used in lab that allows a solution to be heated for a certain amount of time once it begins boiling. Suction filtration is a separation technique that is combined with a water aspirator and was used to collect the product from this experiment, which was 2-methylphenooxyacetic acid. Reaction Scheme: (Draw reaction scheme here) In this …show more content…
Upon the addition of water, it was noted that a layer separation occurred and the water layer remained on top, with the 2-methylphenol layer on the bottom layer. Then, conversion calculations were performed to determine the appropriate amount of 3M NaOH to be added to the 2-methylphenol solution. From the calculations, it was determined that 1.08 mL were to be added. 3M NaOH itself was a cloudy solution in appearance and upon the addition of 3M NaOH to the 2-methylphenol solution, it was noted a color change occurred and it became a yellow-green solution. Following this, the same calculations used previously, were used to determine the appropriate amount of sodium chloroacetate, which was found to be 0.38 g (3.26 mmol). Sodium choloroacetate was a white, crushed solid that was then combined with 1 mL of water and was swirled until the sodium chloroacetate completely dissolved. This sodium choloracetate solution was then transferred to the 2-methylphenol solution by the use of a medicine
And finally into test tube 3, I pipetted 1.0 ml turnip extract and 4.0 ml of water. The contents of test tube 1 was poured into a spectrometer tube and labeled it “B” for blank. “B” tube was now inserted it into the spectrometer. An adjustment to the control knob was made to zero the absorbance reading on the spectrometer since one cannot continue the experiment if the spectrometer is not zeroed. A combination of two people and a stop watch was now needed to not only record the time of the reaction, but to mix the reagents in a precise and accurate manner. As my partner recorded the time, I quickly poured tube 3 into tube 2. I then poured tube 2 into the experiment spectrometer tube labeled “E” and inserted it into the spectrometer. A partner then recorded the absorbance reading for every 20 seconds for a total of 120 seconds. After the experiment, a brown color in the tube should be observed to indicate the reaction was carried out. Using sterile techniques, any excess liquid left was disposed
Different reagents were used for the tests with the reagents reacting with the molecules in a specific way indicated by a change of color. Controls were provided to ensure integrity of the process. The results indicated the presence or absence of the organic molecules in the various substances provided. They proved that using these tests, one can accurately determine what organic molecules a substance contains. This will help in determining the composition of various substances within the cell or even outside the body and how they affect normal cell
A chemical reaction is when substances (reactants) change into other substances (products). The five general types of chemical reactions are synthesis (also known as direct combination), decomposition, single replacement (also known as single displacement), double replacement (also known as double displacement), and combustion. In this lab, the five general types of chemical reactions were conducted and observations were taken before, during, and after the reaction. Then the reactants and observations were used to determine the products to form a balanced chemical equation. The purpose of this lab was to learn and answer the question: How can observations be used to determine the identity of substances produced in a chemical reaction?
3.0g of salicylic acid was weighed then 3.0mL of acetic anhydride and 6 drops of 85% H3PO4 were added to it. The mixture was warmed over a water bath for 5 minutes while stirring. After warming, 20 drops of distilled water was slowly added. 15mL of water was added then the solution was heated until it became clear. It was allowed to cool and was placed in an ice bath until the solution becomes cloudy. Using pre-weighed filter paper, the mixture was filtered and was allowed to dry in the filter paper.
There are millions of different organic compounds. Most of them are found in mixtures and in order to achieve a pure form they need to be separated, isolated, and purified. However, there are endless numbers of possible mixtures, which make it impossible to have a pre-designed procedure for every mixture. So chemists often have to make their own procedures. The purpose of this experiment was to prepare the student to the real world by them designing their own procedure which will help them understand the techniques of separation and purification better. The goal was to extract two of the components of the
We used TLC analysis to identify each product obtained from the dihydroxylation reactions by spotting a TLC plate with the product of our reaction, a solution of cis-cyclohexane, trans-cyclohexane, and a 50:50 mixture of the two. We then placed the plate in a beaker with ethyl acetate saturating the atmosphere to allow the TLC plate to develop. Finally, we compared Rf values of the components of the mobile phase, after the phase was completed. 100% ethyl acetate was used instead of 100% Hexane or a mixture of Ethyl Acetate, because ethyl acetate has high polarity and can separate the components of a mixture to elution, unlike hexane, which is non-polar, and therefore unable to separate the components of the mixture. A 50:50 mixture of both would not work, because the polar and non-polar compounds would neutralize the mixture, and thereby not separate the components of the mixture.
We only added a small amount of HCl to the water and sodium chloride. We did not continue to add more HCl after a significant drop in pH was recorded. We added a total of 2 mL of HCl to both H20 and NaCl before the pH changed. The 1 gram solution of sodium acetate and acetic acid changed after a 8 mL, and the other two never dropped before we reached our total of 10 mL HCl.
The absorbance is proportional to the concentration of the chlorine dioxide in water. Indicators used for this technique include N,N-diethyl-p-phenylenediamine, chlorophenol red, and methylene blue (APHA 1998; Fletcher and Hemming 1985; Quentel et al. 1994; Sweetin et al. 1996). For example, chlorophenol red selectively reacts with chlorine dioxide at pH 7 with a detection limit of 0.12 mg/L. The interferences from chlorine may be reduced by the addition of oxalic acid, sodium cyclamate, or thioacetamide (Sweetin et al. 1996). APHA Method 4500-CLO2-B, iodometric titration analysis, measures the concentration of chlorine dioxide in water by titration with iodide, which is reduced to form iodine. Iodine is then measured colorimetrically when a blue color forms from the production of a starch-iodine complex. The detection limit for this method is 20 µg/L (APHA 1998).
This experiment was designed by conducting a substitution reaction to construct a complex compound (2-methylphenoxyacetic acid) from two simple parts; also known as synthesis - converting simple molecules into more complex molecules. A purification technique known as crystallization was used to purify the product. Suction filtration was used to filter out the product. The experiment was completed over a three-day experimental period.
The purpose of this experiment is to determine the nucleophilic strength of chloride and bromide ions as it reacts with 1-butanol (n-butyl) and 2-methyl-2-propanol (t-butyl alcohol) under SN1 and SN2 conditions.
Purpose: The purpose of this experiment was to observe the many physical and chemical properties of copper as it undergoes a series of chemical reactions. Throughout this process, one would also need to acknowledge that even though the law of conservation of matter/mass suggests that one should expect to recover the same amount of copper as one started with, inevitable sources of error alter the results and produce different outcomes. The possible sources of error that led to a gain or loss in copper are demonstrated in the calculation of percent yield (percent yield= (actual yield/theoretical yield) x 100.
Prepare a solution of sodium acetate (NaOAc) by dissolving 0.5 g anhydrous sodium acetate in 3 mL distilled water in a small beaker.
The purpose of this lab was to standardize the NaOH and then use the standardized NaOH to find the molarity of acetic acid or vinegar. We standardized the NaOH so that the molarity would be as accurate as possible to then find the molarity of vinegar in the next lab. The results for the lab resulted in the NaOH being .193M. In the second lab, we used the .193M of NaOH to find the molarity of the vinegar. The balanced equation is NaOH(aq)+HC2H3O2(aq)= H2O(l)+NaC2H3O2(aq)which is why the phenolphthalein turned pink. From our lab results, we found that the molarity of the vinegar was .856M. The class average was........ One source of error was that the solution was dark pink in color. This would cause the amount of sodium hydroxide used to go
Introduction:-. To natural science the substitution responses is the The greater part significant reactions, particularly Nucleophilic fragrant substitution responses the place nucleophile strike sure charge alternately incompletely certain accuse Concerning illustration it can so, it replaces An weaker nucleophile which after that gets to be An abandoning bunch. The remaining sure alternately incompletely certain particle gets a electrophile. The general type of the response is:. Nuc: + R-LG
Equipment, Materials, and Method The equipment used were a jacketed batch reactor beaker, cooling water circulation system, computer, LabPro temperature probe and conductivity probe, mixing stand and magnetic stir bar. The materials used for this reaction were a 0.08M NaOH solution and a 0.1M ethyl acetate solution. A 20% excess Ethyl acetate was used to ensure NaOH was the limiting reactant.[1] NaOH was chosen for the limiting reactant because of its high conductivity relative to Ethyl acetate. The extent of the reaction was monitored by measuring the conductivity throughout the reaction. With NaOH being the limiting reactant, the change in conductivity is more visible, and the termination of the reaction can